How to remove and install a power steering pump on 2007 through 2011 Toyota Avalon?

Disconnect the cable from the negative battery terminal. Using a large syringe or suction gun, siphon as much fluid out of the power steering fluid reservoir as possible. Place a drain pan under the vehicle to catch any fluid that spills out when the hoses are disconnected. Loosen the right front wheel lug nuts. Raise the vehicle and support it securely on jackstands. Remove the right front wheel. Remove the right front fender apron seal by removing the three screws and the plastic inner seal from the fender well. Remove the drive belt. Detach the fluid feed hose from the pump. Remove the banjo bold and the feed line fitting bolt. Disconnect the electrical connector from the Power Steering Pressure switch. Remove the pressure line-to-pump union bolt and separate the line from the pump. Use two wrenches, one to hold the pressure port fitting and one to hold the union bolt. Remove the sealing washers on each side of the fitting - these should be replaced when installing the pump. Working through the power steering pulley, loosen the pump mounting bolts completely. Turn the pulley until an opening is over the upper bolt for access. Lower the pump and remove the mounting bolts, then remove the pump. Installation is the reverse of removal. Be sure to tighten the pressure line banjo bolt and the feed line fitting bolt. Adjust the drive belt tension. Top up the fluid level in the reservoir and bleed the system.

Genuine Toyota Avalon Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Power Steering Pumps found

View related parts
Toyota Avalon Pump Assembly, VANE
Part Number: 44310-07040
$295.68 MSRP: $423.98
You Save: $128.30 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2012 Toyota Avalon | Limited, XL, XLS | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSX30L-AEAGKA, GSX30L-AEANKA, GSX30L-AEAPKA, GSX30L-AETGKA, GSX30L-AETNKA, GSX30L-AETPKA
View related parts
Toyota Avalon Pump Assy, Vane
Part Number: 44320-07011
$288.02 MSRP: $413.00
You Save: $124.98 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: (L)
- Replaced by: 44320-07012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1998 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK
View related parts
Toyota Avalon Pump Assy, Vane
Part Number: 44320-07010
$288.02 MSRP: $413.00
You Save: $124.98 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 44320-07012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1996 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK
View related parts
Toyota Avalon Pump Assy, Vane
Part Number: 44320-07012
$288.02 MSRP: $413.00
You Save: $124.98 (31%)
Product Specifications
- Other Name: Power Steering Pump
- Manufacturer Note: (L)
- Replaces: 44320-33110, 44320-33111, 44320-07010, 44320-07011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2004 Toyota Avalon | XL, XLS | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCX10L-AEPGKA, MCX10L-AEPGKK, MCX10L-AEPNKA, MCX10L-AEPNKK, MCX10L-AESGKA, MCX10L-AESGKK, MCX10L-AESNKA, MCX10L-AESNKK, MCX20L-AEPGKA, MCX20L-AEPGKK, MCX20L-AEPNKA, MCX20L-AEPNKK, MCX20L-AESGKA, MCX20L-AESNKA

Toyota Avalon Power Steering Pump

The Power Steering Pump of Toyota Avalon vehicles is a working component that creates hydraulic pressure and force needed to ease steering. With the help of hydraulic power, the pump removes the extra load of turning the steering wheel and makes it much easier for the drivers to manage their vehicles on the road. Toyota Avalon Power Steering Pump employs hydraulic actuators to boost the steering force; there is a linkage between the wheels and the steering wheel in case of the electrical system power outage. Different types of power steering systems are hydraulic, electric, and electronic and the Toyota Avalon automobiles enables the driver to exert little effort while steering particularly at slow rates and at standstill.

If you are in demand for superior quality and affordable OEM Toyota Avalon Power Steering Pump, then shop with us! We own a wide range of the reduced-priced genuine Toyota Avalon Power Steering Pump. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Avalon Power Steering Pump Parts Questions & Experts Answers

Pump Assembly, VANE
44310-07040
Q: How to remove and install a power steering pump on 2007 through 2011 Toyota Avalon?
A: Disconnect the cable from the negative battery terminal. Using a large syringe or suction gun, siphon as much fluid out of the power steering fluid reservoir as possible. Place a drain pan under the vehicle to catch any fluid that spills out when the hoses are disconnected. Loosen the right front wheel lug nuts. Raise the vehicle and support it securely on jackstands. Remove the right front wheel. Remove the right front fender apron seal by removing the three screws and the plastic inner seal from the fender well. Remove the drive belt. Detach the fluid feed hose from the pump. Remove the banjo bold and the feed line fitting bolt. Disconnect the electrical connector from the Power Steering Pressure Switch. Remove the pressure line-to-pump union bolt and separate the line from the pump. Use two wrenches, one to hold the pressure port fitting and one to hold the union bolt. Remove the sealing washers on each side of the fitting - these should be replaced when installing the pump. Working through the power steering pulley, loosen the pump mounting bolts completely. Turn the pulley until an opening is over the upper bolt for access. Lower the pump and remove the mounting bolts, then remove the pump. Installation is the reverse of removal. Be sure to tighten the pressure line banjo bolt and the feed line fitting bolt. Adjust the drive belt tension. Top up the fluid level in the reservoir and bleed the system.