How to remove and install Clutch Fork and Release Bearing on Toyota Camry?

The procedure for removal applies to 2009 and earlier models only, as 2010 and later models have the clutch release bearing and release cylinder as a single assembly that cannot be replaced separately. Begin by disconnecting the negative cable from the battery. Next, remove the transaxle. Reach behind the clutch fork to disengage it from the ballstud by pulling on the retention spring, then remove the fork and bearing. For inspection, hold the bearing by the outer race and rotate the inner race while applying pressure; it should turn smoothly. If it does not, replace the bearing/hub assembly. Wipe the bearing with a clean rag and inspect for damage, wear, and cracks, avoiding immersion in solvent as it is sealed for life. Also, check the clutch fork for any cracks and bends. For installation, fill the inner groove of the release bearing with high-temperature grease and apply a light coat of the same grease to the transaxle input shaft splines and the sleeve of the transaxle front bearing retainer. Lubricate the clutch fork ball socket, fork ends, and release cylinder pushrod socket with high-temperature grease. Attach the release bearing to the clutch fork, then slide the release bearing onto the transaxle input shaft front bearing retainer while passing the end of the clutch fork through the opening in the clutch housing. Push the clutch fork onto the ball stud until it is firmly seated, and apply a light coat of high-temperature grease to the face of the release bearing where it contacts the pressure plate diaphragm fingers. The remainder of the installation follows the reverse order of removal.

Genuine Toyota Camry Release Bearing

Clutch Release Throw Out Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Release Bearings found

View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-33020
$66.21 MSRP: $93.33
You Save: $27.12 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Bearing
- Manufacturer Note: PNC 31232A=TYPE A
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2009 Toyota Camry | LE, SE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV40L-AEMNKA, ACV40L-CEMNKA, ACV40L-CEMSKA
View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-20190
$50.53 MSRP: $70.63
You Save: $20.10 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Replaced by: 31230-20191
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Camry | CE, LE | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-CEMDKA, MCV20L-CEMNKA
- 1992-1994 Toyota Camry | LE, SE | 6 Cyl 3.0L | 3VZFE; 3VZFE; VCV10L-AEMNKK, VCV10L-AEMSKA, VCV10L-CEMSKA
View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-20191
$50.53 MSRP: $70.63
You Save: $20.10 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Bearing
- Manufacturer Note: PNC 31232A=TYPE B
- Replaces: 31230-20190
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Toyota Camry | LE, SE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV40L-AEMNKA, ACV40L-CEMNKA, ACV40L-CEMSKA
- 1997-2001 Toyota Camry | CE, LE | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-CEMDKA, 1MZFE; MCV20L-CEMNKA, MCV20L-CEMNKA
- 1992-1994 Toyota Camry | LE, SE | 6 Cyl 3.0L | 3VZFE; 3VZFE; VCV10L-AEMNKK, VCV10L-AEMSKA, VCV10L-CEMSKA
View More
View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-20170
$70.04 MSRP: $98.74
You Save: $28.70 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Bearing
- Replaces: 31230-20160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2007 Toyota Camry | LE, SE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-AEMNKA, ACV30L-AEMSKA, ACV40L-AEMNKA, ACV40L-CEMNKA, ACV40L-CEMSKA
- 1987-1991 Toyota Camry | DX, LE | 4 Cyl 2.0L, 4 Cyl 2.5L | 2VZFE, 3SFE; 2VZFE, 3SFE; SV25L-UEMDKA, SV25L-UEMDKK, SV25L-UEMNKA, SV25L-UEMNKK, VZV21L-AEMDKA, VZV21L-UEMDKA, VZV21L-UEMNKA, VZV21L-UEMNKK
View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-32060
$74.29 MSRP: $104.73
You Save: $30.44 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Bearing
- Replaces: 31230-32080, 31230-32070, 31230-32090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-2001 Toyota Camry | CE, DX, LE, STD | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SFE, 5SFE; 3SFE, 5SFE; SV21L-AEMBKA, SV21L-AEMDKA, SV21LG-UWMDKK, SV21L-UEMBKA, SV21L-UEMDKA, SV21L-UEMDKK, SV21L-UEMNKK, SXV10L-AEMDKA, SXV10L-AEMDKK, SXV10L-AEMNKK, SXV10L-CCMDKA, SXV10L-CCMDKK, SXV10L-CCMNKK, SXV10L-CEMDKA, SXV10L-CEMDKK, SXV10L-CEMNKK, SXV10L-CWMDKK, SXV20L-CEMDKA, SXV20L-CEMDKK, SXV20L-CEMNKK
View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-32020
$46.52 MSRP: $65.02
You Save: $18.50 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: NACHI
- Replaced by: 31230-32100-77
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1987-1991 Toyota Camry | DX, LE, STD | 4 Cyl 2.0L | 3SFE; 3SFE; SV21L-AEMBKA, SV21L-AEMDKA, SV21LG-UWMDKA, SV21LG-UWMDKK, SV21L-UEMBKA, SV21L-UEMBKK, SV21L-UEMDKA, SV21L-UEMDKK, SV21L-UEMNKA, SV21L-UEMNKK
View related parts
Toyota Camry Bearing Assy, Clutch Release
Part Number: 31230-32010
$46.52 MSRP: $65.02
You Save: $18.50 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: KOYO
- Replaced by: 31230-32100-77
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1983-1987 Toyota Camry | DLX, DX, LE | 4 Cyl 1.8L, 4 Cyl 2.0L | 1CTLC, 2SELC, 3SFE; 1CTLC, 2SELC, 3SFE; CV10L-UEMNXA, SV11L-UEMEEA, SV11L-UEMEEK, SV11L-UEMNEA, SV11L-UEMNEK, SV11L-UHMEEA, SV11L-UHMEEK, SV11L-UHMNEA, SV21LG-UWMDKA, SV21LG-UWMDKK, SV21L-UEMDKA, SV21L-UEMDKK, SV21L-UEMNKA, SV21L-UEMNKK

Toyota Camry Release Bearing

If you are in demand for superior quality and affordable OEM Toyota Camry Release Bearing, then shop with us! We own a wide range of the reduced-priced genuine Toyota Camry Release Bearing. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Camry Release Bearing Parts Questions & Experts Answers

Bearing Assy, Clutch Release
31230-20191
Q: How to remove and install Clutch Fork and Release Bearing on Toyota Camry?
A: The procedure for removal applies to 2009 and earlier models only, as 2010 and later models have the clutch release bearing and release cylinder as a single assembly that cannot be replaced separately. Begin by disconnecting the negative cable from the battery. Next, remove the transaxle. Reach behind the clutch fork to disengage it from the ballstud by pulling on the retention spring, then remove the fork and bearing. For inspection, hold the bearing by the outer race and rotate the inner race while applying pressure; it should turn smoothly. If it does not, replace the bearing/hub assembly. Wipe the bearing with a clean rag and inspect for damage, wear, and cracks, avoiding immersion in solvent as it is sealed for life. Also, check the clutch fork for any cracks and bends. For installation, fill the inner groove of the release bearing with high-temperature grease and apply a light coat of the same grease to the transaxle input shaft splines and the sleeve of the transaxle front bearing retainer. Lubricate the clutch fork ball socket, fork ends, and release cylinder pushrod socket with high-temperature grease. Attach the release bearing to the clutch fork, then slide the release bearing onto the transaxle input shaft front bearing retainer while passing the end of the clutch fork through the opening in the clutch housing. Push the clutch fork onto the ball stud until it is firmly seated, and apply a light coat of high-temperature grease to the face of the release bearing where it contacts the pressure plate diaphragm fingers. The remainder of the installation follows the reverse order of removal.