How do you remove and install the combination switch on Toyota Celica?

To replace the combination switch on 1990 and later models, try reaching the combination switch with your left hand and the negative cable from the battery with your right hand while trending new blip lines. Subsequently, extract the lower finish panel together with the steering wheel and the steering column cover. Then, remove the four screws , which retain the combination switch, follow the harness down the steering column to the connector and release any wire retainer clips if existed. Remove the connector and shift the switch off the column; to install, reverse the procedure. To replace the turn signal/headlight control switch, one has to expel the combination switch then take out the screws present on the front side of the combination switch In addition, one has to disconnect the locking tab of the lever and finally, one is required to push the lever forward and upwards to unlock it. In terms of installation, the operation is the reverse of removal; pull the wiring terminals of the switch from the electrical connector. For the cruise control switch, you will need to unscrew two retaining screws, disconnect the electrical connector, and then remove the switch off the combination switch and then disconnect the switch wiring terminals from the electrical connector; to install, reverse the mentioned procedures. For the wiper/washer control switch, prayers the switch using the front retaining screws and the four rear retention screws follow by disconnecting the switch wiring terminals from its electrical connector and to replace it, the procedures is in reverse. To remove all the electrical connectors, you have to trace the wiring harness from switch to electrical connector then apply the tape on wires and terminals to make it easier. As for the combination switch cover, this is opened by using a small screwdriver or punch for accessing the terminals; to remove it, one just has to force down the locking lug; to join it, simply slot the terminal into the connector through a push action with the locking lug lodging into place; the final touch is to close the connector cover to lock the terminals.

Genuine Toyota Celica Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

58 Turn Signal Switches found

View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2B580
$146.12 MSRP: $207.74
You Save: $61.62 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W/*RW
- Replaced by: 84310-2B670
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1986-1987 Toyota Celica | GT | 4 Cyl 2.0L | 2SELC, 3SFE; 2SELC, 3SFE; ST161L-BLMVEA, ST161L-BLMVEK, ST161L-BLPVEA, ST161L-BLPVEK, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2B610
$170.50 MSRP: $242.40
You Save: $71.90 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W/*RW & *VIW
- Replaced by: 84310-2B680
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1986-1987 Toyota Celica | GT, GTS | 4 Cyl 2.0L | 2SELC, 3SFE, 3SGELC; 2SELC, 3SFE, 3SGELC; ST161L-BLMVEA, ST161L-BLMVEK, ST161L-BLPVEA, ST161L-BLPVEK, ST162L-BLMVFA, ST162L-BLMVFK, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK
View related parts
Toyota Celica Switch, Turn Signal
Part Number: 84329-12030
$44.90 MSRP: $62.75
You Save: $17.85 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Turn Signal Switch
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988 Toyota Celica | GT, ST | 4 Cyl 2.0L | 3SFE; 3SFE; ST162L-BCMSKA, ST162L-BCMVKA, ST162L-BCPSKA, ST162L-BCPVKA, ST162L-BCPVKK, ST162L-BKMVKA, ST162L-BKPVKA, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2B390
$153.75 MSRP: $218.58
You Save: $64.83 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W/*CRC
- Replaced by: 84310-2B410
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1986-1987 Toyota Celica | GT | 4 Cyl 2.0L | 3SFE; 3SFE; ST162L-BCMVKA, ST162L-BCPVKA, ST162L-BCPVKK, ST162L-BKMVKA, ST162L-BKPVKA, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L670
$405.36 MSRP: $596.69
You Save: $191.33 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Combo Switch, Turn Signal Switch
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BCMGKA, ST204L-BCMSKA, ST204L-BCPGKA, ST204L-BCPSKA, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L650
$415.61 MSRP: $611.79
You Save: $196.18 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W(CRUISE CONTROL & FOG LAMP)
- Replaced by: 84310-33810
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BCMGKA, ST204L-BCMSKA, ST204L-BCPGKA, ST204L-BCPSKA, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L710
$417.33 MSRP: $614.31
You Save: $196.98 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W(CRUISE CONTROL & REAR WIPER)
- Replaced by: 84310-3D020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPGKK, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L060
$198.96 MSRP: $285.30
You Save: $86.34 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 84310-2L080
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1996 Toyota Celica | GT, ST | 4 Cyl 1.8L, 4 Cyl 2.2L | 5SFE, 7AFE; 5SFE, 7AFE; AT200L-BCMSKA, AT200L-BCPSKA, AT200L-BLMSKA, AT200L-BLPSKA, ST204L-BCMGKA, ST204L-BCPGKA, ST204L-BKMGKA, ST204L-BKPGKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L080
$198.96 MSRP: $285.30
You Save: $86.34 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Combo Switch, Turn Signal Switch
- Replaces: 84310-2L060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1996 Toyota Celica | GT, ST | 4 Cyl 1.8L, 4 Cyl 2.2L | 5SFE, 7AFE; 5SFE, 7AFE; AT200L-BCMSKA, AT200L-BCPSKA, AT200L-BLMSKA, AT200L-BLPSKA, ST204L-BCMGKA, ST204L-BCMGKK, ST204L-BCPGKA, ST204L-BCPGKK, ST204L-BKMGKA, ST204L-BKPGKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L070
$215.92 MSRP: $309.62
You Save: $93.70 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W(REAR WIPER)
- Replaced by: 84310-2L100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1996 Toyota Celica | GT, ST | 4 Cyl 1.8L, 4 Cyl 2.2L | 5SFE, 7AFE; 5SFE, 7AFE; AT200L-BLMSKA, AT200L-BLPSKA, ST204L-BLMGKA, ST204L-BLPGKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L680
$225.04 MSRP: $322.69
You Save: $97.65 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Combo Switch, Turn Signal Switch
- Manufacturer Note: W(REAR WIPER)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BLMGKA, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L660
$282.73 MSRP: $405.41
You Save: $122.68 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: W(CRUISE CONTROL & FOG LAMP & REAR WIPER)
- Replaced by: 84310-3D060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPGKK, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-2L320
$302.82 MSRP: $434.22
You Save: $131.40 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Combo Switch, Turn Signal Switch
- Manufacturer Note: W(CRUISE CONTOROL)
- Replaces: 84310-42050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1998 Toyota Celica | GT, ST | 4 Cyl 1.8L, 4 Cyl 2.2L | 5SFE, 7AFE; 5SFE, 7AFE; AT200L-BLMSKA, AT200L-BLMSKK, AT200L-BLPSKA, AT200L-BLPSKK, ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPGKK, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-3D010
$316.34 MSRP: $453.62
You Save: $137.28 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 84310-06180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BCMGKA, ST204L-BCMSKA, ST204L-BCPGKA, ST204L-BCPSKA, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPSKA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-14171
Product Specifications
- Replaced by: 84310-14172
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.7L | 20R, 4ME; 20R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-14172
Product Specifications
- Replaces: 84310-14170, 84310-14171
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | GT, LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 4ME; 20R, 22R; RA43L-BCMQSA, 4ME; MA46L-BLMQEA, RA42L-BCHDSA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-14161
Product Specifications
- Manufacturer Note: W/TILT STEERING
- Replaced by: 84310-14162
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.7L | 20R, 4ME; 20R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA
View related parts
Toyota Celica Switch Assy, Turn Signal
Part Number: 84310-14162
Product Specifications
- Manufacturer Note: W/TILT STEERING
- Replaces: 84310-14160, 84310-14161
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | GT, LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 4ME; 20R, 22R; RA43L-BCMQSA, 4ME; MA46L-BLMQEA, RA42L-BCHDSA
View related parts
Toyota Celica Switch Assembly, Turn Signal
Part Number: 84310-12260
Product Specifications
- Other Name: Switch Assy, Turn Signal
- Manufacturer Note: W/INTERMITTENT WIPER
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1978-1980 Toyota Celica | LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.7L | 20R, 4ME; 20R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA
View related parts
Toyota Celica Switch Assembly, Turn Signal
Part Number: 84310-14080
Product Specifications
- Other Name: Switch Assy, Turn Signal
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1980 Toyota Celica | LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.7L | 20R, 4ME; 20R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA

| Page 1 of 3 |Next >

1-20 of 58 Results

Toyota Celica Turn Signal Switch

If you are in demand for superior quality and affordable OEM Toyota Celica Turn Signal Switch, then shop with us! We own a wide range of the reduced-priced genuine Toyota Celica Turn Signal Switch. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Celica Turn Signal Switch Parts Questions & Experts Answers

Switch Assy, Turn Signal
84310-2B660
Q: How do you remove and install the combination switch on Toyota Celica?
A: To replace the combination switch on 1990 and later models, try reaching the combination switch with your left hand and the negative cable from the battery with your right hand while trending new blip lines. Subsequently, extract the lower finish panel together with the steering wheel and the steering column cover. Then, remove the four screws , which retain the combination switch, follow the harness down the steering column to the connector and release any wire retainer clips if existed. Remove the connector and shift the switch off the column; to install, reverse the procedure. To replace the turn signal/headlight control switch, one has to expel the combination switch then take out the screws present on the front side of the combination switch In addition, one has to disconnect the locking tab of the lever and finally, one is required to push the lever forward and upwards to unlock it. In terms of installation, the operation is the reverse of removal; pull the wiring terminals of the switch from the electrical connector. For the cruise control switch, you will need to unscrew two retaining screws, disconnect the electrical connector, and then remove the switch off the combination switch and then disconnect the switch wiring terminals from the electrical connector; to install, reverse the mentioned procedures. For the wiper/washer control switch, prayers the switch using the front retaining screws and the four rear retention screws follow by disconnecting the switch wiring terminals from its electrical connector and to replace it, the procedures is in reverse. To remove all the electrical connectors, you have to trace the wiring harness from switch to electrical connector then apply the tape on wires and terminals to make it easier. As for the combination switch cover, this is opened by using a small screwdriver or punch for accessing the terminals; to remove it, one just has to force down the locking lug; to join it, simply slot the terminal into the connector through a push action with the locking lug lodging into place; the final touch is to close the connector cover to lock the terminals.