How to remove and install the cylinder head in Four cylinder engine on Toyota Highlander?

To remove the cylinder head, first relieve the fuel system pressure and disconnect the cable from the negative terminal of the battery, then drain the engine coolant. Next, remove the drivebelt and alternator, followed by the valve cover, throttle body, fuel injectors, fuel rail, intake manifold, and exhaust manifold. Remove the timing chain and camshaft sprockets, ensuring the engine is supported from below with a floor jack and a block of wood after the pressed steel portion of the oil pan is removed. For 2008 and later models, remove the camshafts, lifters, and camshaft housing. Label and disconnect the coolant hoses and electrical connections from the cylinder head, loosening the cylinder head bolts in 1/4-turn increments until they can be removed by hand, following the reverse order of the tightening sequence. Lift the cylinder head off the engine block, prying carefully if it is stuck, and remove any remaining external components for thorough cleaning and inspection. For installation, ensure the mating surfaces of the cylinder head and block are perfectly clean, using a gasket scraper and brake system cleaner to remove all traces of carbon and old gasket material. Stuff the cylinders with clean shop rags to keep out debris and use a vacuum cleaner to remove any material that falls into the cylinders. Check the mating surfaces for damage, chasing the threads in the cylinder head bolt holes with a tap and cleaning them with compressed air. Install the components that were removed, position the new gasket over the dowel pins in the block, and apply RTV sealant to the ends of the cylinder head gasket. Carefully set the cylinder head on the block without disturbing the gasket, apply clean engine oil to the threads and under the bolt heads of the new cylinder head bolts, and tighten them finger tight before following the recommended sequence for final tightening. The remainder of the installation follows the reverse order of removal, with a caution to wait at least four hours before adding oil and coolant and starting the engine. For 1999 through 2007 models, check and adjust the valves as necessary, change the engine oil and filter, refill the transfer case for 4WD models, and refill the cooling system, running the engine to check for leaks.

Genuine Toyota Highlander Cylinder Head

Head

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

56 Cylinder Heads found

View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-39776
$863.53 MSRP: $1081.02
You Save: $217.49 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder; Cylinder Head
- Replaces: 11101-09346, 11101-39715, 11101-09345
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2019 Toyota Highlander | STD | 4 Cyl 2.7L | 1ARFE; 1ARFE; ASU40L-ARTNKA, 1ARFE; ASU50L-ARTNKA, ASU40L-BRTNKA, ASU50L-ARTNKA
View related parts
Toyota Highlander Head Sub-Assy, Cylinder
Part Number: 11101-28012
$639.00 MSRP: $807.34
You Save: $168.34 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaces: 11101-0H040, 11101-0H011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Highlander | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA
View related parts
Toyota Highlander Head Sub-Assembly, CYLIN
Part Number: 11101-F9001
$864.55 MSRP: $1082.30
You Save: $217.75 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaces: 11101-F9000, 11101-29626, 11101-29625
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Highlander | 4 Cyl 2.5L | A25AFXS; A25AFXS; AXUH70L-ARXGHA, AXUH70L-ARXMHA, AXUH70L-ARXNHA, AXUH78L-ARXGHA, AXUH78L-ARXMHA, AXUH78L-ARXNHA
View related parts
Toyota Highlander HEAD SUB-ASSY, CYLIN
Part Number: 11101-F9002
$862.73 MSRP: $1080.02
You Save: $217.29 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2022 Toyota Highlander
View related parts
Toyota Highlander HEAD SUB-ASSY, CYLIN
Part Number: 11101-09552
$879.60 MSRP: $1101.14
You Save: $221.54 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaces: 11101-09551, 11101-09550
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2022 Toyota Highlander | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GSU50L-ARZGHA, 2GRFKS; GSU70L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA, GSU70L-ARZGHA, GSU70L-ARZMHA, GSU70L-ARZNHA, GSU70L-ARZSHA, GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA, GSU75L-ARZSHA
View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-39715
$863.53 MSRP: $1081.02
You Save: $217.49 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder
- Replaced by: 11101-39776
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2012 Toyota Highlander | STD | 4 Cyl 2.7L | 1ARFE; 1ARFE; ASU40L-ARTNKA, ASU40L-BRTNKA
View related parts
Toyota Highlander Head, Cylinder, LH
Part Number: 11102-29075
$958.45 MSRP: $1199.85
You Save: $241.40 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Position: Driver Side
- Replaces: 11102-09050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2011 Toyota Highlander | Limited, STD | 6 Cyl 3.3L | 3MZFE; 3MZFE; MCU23L-BRANKA, MCU23L-BWANKA, MCU28L-BRANKA, MCU28L-BWANKA, MHU23L-BRXNKA, MHU23L-BWXNKA, MHU28L-BRXNKA, MHU28L-BWXNKA, MHU48L-BRXMKA, MHU48L-BRXNKA
View related parts
Toyota Highlander Head Sub-Assy, Cylinder
Part Number: 11101-0H011
$639.00 MSRP: $807.34
You Save: $168.34 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 11101-28012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2007 Toyota Highlander | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA
View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-F9000
$864.55 MSRP: $1082.30
You Save: $217.75 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assembly, CYLIN
- Replaced by: 11101-F9001
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2021 Toyota Highlander | 4 Cyl 2.5L | A25AFXS; A25AFXS; AXUH70L-ARXGHA, AXUH70L-ARXMHA, AXUH70L-ARXNHA, AXUH78L-ARXGHA, AXUH78L-ARXMHA, AXUH78L-ARXNHA
View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-09550
$879.60 MSRP: $1101.14
You Save: $221.54 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder
- Replaced by: 11101-09552
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2019 Toyota Highlander | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GSU50L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA
View related parts
Toyota Highlander Head Sub-Assembly, CYLIN
Part Number: 11102-09201
$888.85 MSRP: $1112.72
You Save: $223.87 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Position: Driver Side
- Replaces: 11102-09200
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2022 Toyota Highlander | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GSU50L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA, GSU70L-ARZGHA, GSU70L-ARZMHA, GSU70L-ARZNHA, GSU70L-ARZSHA, GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA, GSU75L-ARZSHA
View related parts
Toyota Highlander Head, Cylinder, LH
Part Number: 11102-09031
$996.99 MSRP: $1248.09
You Save: $251.10 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side
- Replaced by: 11102-29058
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2004 Toyota Highlander | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCU20L-BWPNKA
View related parts
Toyota Highlander Head, Cylinder, LH
Part Number: 11102-29057
$996.99 MSRP: $1248.09
You Save: $251.10 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side
- Replaced by: 11102-29058
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2004 Toyota Highlander | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCU20L-BWPNKA, MCU25L-BWPNKA
View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-09262
$1230.41 MSRP: $1540.30
You Save: $309.89 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder; Cylinder Head
- Replaces: 11101-09260, 11101-09261, 11101-39535, 11101-39536
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2016 Toyota Highlander | Grande, Limited, Medium, STD, Sport | 6 Cyl 3.5L | 2GRFE, 2GRFXE; 2GRFE, 2GRFE; GSU40L-ARAGKA, 2GRFE; GSU50L-ARTGKA, 2GRFXE; GSU40L-ARAGKA, GSU40L-ARAMKA, GSU40L-ARANKA, GSU40L-ARASKA, GSU40L-BRAGKA, GSU40L-BRAMKA, GSU40L-BRANKA, GSU40L-BRASKA, GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA, GSU45L-BRAGKA, GSU45L-BRAMKA, GSU45L-BRANKA, GSU45L-BRASKA, GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GVU48L-BRXGKA, GVU48L-BRXNKA, GVU58L-ARXGKA, GVU58L-ARXMKA, GVU58L-ARXNKA
View related parts
Toyota Highlander Head Sub-Assy, Cylinder
Part Number: 11101-0H010
$717.12 MSRP: $897.73
You Save: $180.61 (21%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaces: 11101-28010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2006 Toyota Highlander | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA
- 2001-2002 Toyota Highlander | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACU20L-BWPNKA, ACU25L-BWPNKA
View related parts
Toyota Highlander HEAD SUB-ASSY, CYLIN
Part Number: 11102-09182
$879.60 MSRP: $1101.14
You Save: $221.54 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Position: Driver Side
- Replaces: 11102-09181, 11102-09180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2022 Toyota Highlander | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GSU50L-ARZGHA, 2GRFKS; GSU70L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA, GSU70L-ARZGHA, GSU70L-ARZMHA, GSU70L-ARZNHA, GSU70L-ARZSHA, GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA, GSU75L-ARZSHA
View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-39536
$1230.41 MSRP: $1540.30
You Save: $309.89 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder
- Replaced by: 11101-09262
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2015 Toyota Highlander | Limited, STD | 6 Cyl 3.5L | 2GRFE, 2GRFXE; 2GRFE, 2GRFXE; GSU40L-ARAGKA, GSU40L-ARANKA, GSU45L-ARAGKA, GSU45L-ARANKA, GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GVU48L-BRXGKA, GVU48L-BRXNKA, GVU58L-ARXGKA, GVU58L-ARXMKA, GVU58L-ARXNKA
View related parts
Toyota Highlander Head Sub-Assy, Cylinder
Part Number: 11101-28011
$639.00 MSRP: $807.34
You Save: $168.34 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Head
- Replaced by: 11101-28012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2006 Toyota Highlander | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA
View related parts
Toyota Highlander Head Sub-Assembly,Cylinder
Part Number: 11101-09345
$863.53 MSRP: $1081.02
You Save: $217.49 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder
- Replaced by: 11101-39776
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2013 Toyota Highlander | STD | 4 Cyl 2.7L | 1ARFE; 1ARFE; ASU40L-ARTNKA
View related parts
Toyota Highlander Head Sub-Assembly, Cylinder
Part Number: 11101-09346
$863.53 MSRP: $1081.02
You Save: $217.49 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Head Sub-Assy, Cylinder
- Replaced by: 11101-39776
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2018 Toyota Highlander | 4 Cyl 2.7L | 1ARFE; 1ARFE; ASU50L-ARTNKA
- 2012-2013 Toyota Highlander | STD | 4 Cyl 2.7L | 1ARFE; 1ARFE; ASU40L-ARTNKA

| Page 1 of 3 |Next >

1-20 of 56 Results

Toyota Highlander Cylinder Head

If you are in demand for superior quality and affordable OEM Toyota Highlander Cylinder Head, then shop with us! We own a wide range of the reduced-priced genuine Toyota Highlander Cylinder Head. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Highlander Cylinder Head Parts Questions & Experts Answers

Head Sub-Assy, Cylinder
11101-28012
Q: How to remove and install the cylinder head in Four cylinder engine on Toyota Highlander?
A: To remove the cylinder head, first relieve the fuel system pressure and disconnect the cable from the negative terminal of the battery, then drain the engine coolant. Next, remove the drivebelt and alternator, followed by the valve cover, throttle body, fuel injectors, fuel rail, Intake Manifold, and Exhaust Manifold. Remove the Timing Chain and camshaft sprockets, ensuring the engine is supported from below with a floor jack and a block of wood after the pressed steel portion of the oil pan is removed. For 2008 and later models, remove the camshafts, lifters, and camshaft housing. Label and disconnect the coolant hoses and electrical connections from the cylinder head, loosening the cylinder head bolts in 1/4-turn increments until they can be removed by hand, following the reverse order of the tightening sequence. Lift the cylinder head off the engine block, prying carefully if it is stuck, and remove any remaining external components for thorough cleaning and inspection. For installation, ensure the mating surfaces of the cylinder head and block are perfectly clean, using a gasket scraper and brake system cleaner to remove all traces of carbon and old gasket material. Stuff the cylinders with clean shop rags to keep out debris and use a vacuum cleaner to remove any material that falls into the cylinders. Check the mating surfaces for damage, chasing the threads in the cylinder head bolt holes with a tap and cleaning them with compressed air. Install the components that were removed, position the new gasket over the dowel pins in the block, and apply RTV sealant to the ends of the cylinder head gasket. Carefully set the cylinder head on the block without disturbing the gasket, apply clean engine oil to the threads and under the bolt heads of the new cylinder head bolts, and tighten them finger tight before following the recommended sequence for final tightening. The remainder of the installation follows the reverse order of removal, with a caution to wait at least four hours before adding oil and coolant and starting the engine. For 1999 through 2007 models, check and adjust the valves as necessary, change the engine oil and filter, refill the transfer case for 4WD models, and refill the cooling system, running the engine to check for leaks.