How to remove and install the driveaxle and steering knuckle on Toyota Highlander?

Before having the drive axle out, the drive axle hub nut and the wheel lug nuts must be loosened and the vehicle has to be raised and supported properly on jack stands before the wheel can be removed. Next it is necessary to loosen the wheel speed sensor from the knuckle and then remove the brake disc from the hub. While maintaining the bolts in position tighten them enough to free the strut from the steering knuckle arm but do not remove the bolts; unscrew the tie-rod end from the steering knuckle arm. Unscrew the ball joint-to-lower arml bolt and nuts to relieve the ball joint from the lower arm, pry the control arm with a pry bar to separate it from the ball joint. Here it is possible to unscrew the strut-to-knuckle bolts and to shift the drive axle away from the hub; it is recommended to thread a piece of wire over the end of the axle to keep it in place. Disconnect the steering knuckle from the strut, in case you have to eliminate the ball joint from the steering knuckle. For installation, position the knuckle and hub assembly to the right place and align the drive axle to the hub. Force the knuckle into the inner part of the strut flange, put on the bolts and nuts, but do not over tighten them at this stage. Place the nut ont the ball joint and bolt in the control arm then tighten it but halfway through in order to fix it. Connect the tie-rod to the steering knuckle arm and then torque the strut bolt nuts, ball joint to control arm bolt and nuts, and the tie-rod nut to the prescribed torque and replace all cotter-pin with new ones. Put the brake disc in the hub and tighten the caliper and the wheel speed sensor. Last, torque the drive axle/hub nut, final torque to be done once the vehicle is in the ground, then fit the wheels with the lug nuts, lower the vehicle ,and finally torque the lug nuts to the required torque. It is therefore necessary to fit the drive axle/hub nut in place, torque it to the necessary measure, and go on to staking the nut.

Genuine Toyota Highlander Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Steering Knuckles found

View related parts
Toyota Highlander Knuckle, Steering, LH
Part Number: 43212-0E010
$319.88 MSRP: $458.68
You Save: $138.80 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Replaces: 43212-48010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2019 Toyota Highlander | Grande, Limited, Medium, STD, Sport | 4 Cyl 2.7L, 6 Cyl 3.3L, 6 Cyl 3.5L | 1ARFE, 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS, 3MZFE; 1ARFE, 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; ASU40L-ARTNKA, 3MZFE; ASU40L-BRTNKA, ASU50L-ARTNKA, GSU40L-ARAGKA, GSU40L-ARAMKA, GSU40L-ARANKA, GSU40L-ARASKA, GSU40L-BRAGKA, GSU40L-BRAMKA, GSU40L-BRANKA, GSU40L-BRASKA, GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA, GSU45L-BRAGKA, GSU45L-BRAMKA, GSU45L-BRANKA, GSU45L-BRASKA, GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU50L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA, GVU48L-BRXGKA, GVU48L-BRXNKA, GVU58L-ARXGHA, GVU58L-ARXGKA, GVU58L-ARXMHA, GVU58L-ARXMKA, GVU58L-ARXNHA, GVU58L-ARXNKA, MHU48L-BRXMKA, MHU48L-BRXNKA
View related parts
Toyota Highlander Knuckle, Steering, RH
Part Number: 43211-0E010
$327.92 MSRP: $470.21
You Save: $142.29 (31%)
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Manufacturer Note: CANADA SPEC
- Position: Passenger Side
- Replaces: 43211-48010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2019 Toyota Highlander | Grande, Limited, Medium, STD, Sport | 4 Cyl 2.7L, 6 Cyl 3.3L, 6 Cyl 3.5L | 1ARFE, 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS, 3MZFE; 1ARFE, 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; ASU40L-ARTNKA, 3MZFE; ASU40L-BRTNKA, ASU50L-ARTNKA, GSU40L-ARAGKA, GSU40L-ARAMKA, GSU40L-ARANKA, GSU40L-ARASKA, GSU40L-BRAGKA, GSU40L-BRAMKA, GSU40L-BRANKA, GSU40L-BRASKA, GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA, GSU45L-BRAGKA, GSU45L-BRAMKA, GSU45L-BRANKA, GSU45L-BRASKA, GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU50L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA, GVU48L-BRXGKA, GVU48L-BRXNKA, GVU58L-ARXGHA, GVU58L-ARXGKA, GVU58L-ARXMHA, GVU58L-ARXMKA, GVU58L-ARXNHA, GVU58L-ARXNKA, MHU48L-BRXMKA, MHU48L-BRXNKA
View related parts
Toyota Highlander Knuckle, Steering, RH
Part Number: 43211-58020
$321.66 MSRP: $461.23
You Save: $139.57 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 2AZFE, 3MZFE; 1MZFE, 2AZFE, 3MZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA, MCU20L-BWPNKA, MCU23L-BRANKA, MCU23L-BWANKA, MCU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA, MHU23L-BRXNKA, MHU23L-BWXNKA, MHU28L-BRXNKA, MHU28L-BWXNKA
View related parts
Toyota Highlander Knuckle, Steering, LH
Part Number: 43212-48010
$319.88 MSRP: $458.68
You Save: $138.80 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side
- Replaced by: 43212-0E010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2013 Toyota Highlander | Grande, Limited, Sport, STD | 4 Cyl 2.7L, 6 Cyl 3.3L, 6 Cyl 3.5L | 1ARFE, 2GRFE, 2GRFXE, 3MZFE; 1ARFE, 2GRFE, 2GRFXE, 3MZFE; ASU40L-BRTNKA, GSU40L-BRAGKA, GSU40L-BRAMKA, GSU40L-BRANKA, GSU40L-BRASKA, GSU45L-BRAGKA, GSU45L-BRAMKA, GSU45L-BRANKA, GSU45L-BRASKA, GVU48L-BRXGKA, GVU48L-BRXNKA, MHU48L-BRXMKA, MHU48L-BRXNKA
View related parts
Toyota Highlander Knuckle, Steering, LH
Part Number: 43212-58020
$318.76 MSRP: $457.08
You Save: $138.32 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 2AZFE, 3MZFE; 1MZFE, 2AZFE, 3MZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA, MCU20L-BWPNKA, MCU23L-BRANKA, MCU23L-BWANKA, MCU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA, MHU23L-BRXNKA, MHU23L-BWXNKA, MHU28L-BRXNKA, MHU28L-BWXNKA
View related parts
Toyota Highlander KNUCKLE Sub-Assembly, St
Part Number: 43202-0E010
$233.26 MSRP: $334.48
You Save: $101.22 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Highlander | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFXS; 2GRFKS, A25AFXS; AXUH70L-ARXGHA, AXUH70L-ARXMHA, AXUH70L-ARXNHA, AXUH78L-ARXGHA, AXUH78L-ARXMHA, AXUH78L-ARXNHA, GSU70L-ARZGHA, GSU70L-ARZMHA, GSU70L-ARZNHA, GSU70L-ARZSHA, GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA, GSU75L-ARZSHA
View related parts
Toyota Highlander Knuckle, Steering, LH
Part Number: 43212-28100
$285.35 MSRP: $409.17
You Save: $123.82 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2004 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 2AZFE, 3MZFE; 1MZFE, 2AZFE, 3MZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA, MCU20L-BWPNKA, MCU23L-BRANKA, MCU23L-BWANKA, MCU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA
View related parts
Toyota Highlander KNUCKLE Sub-Assembly, St
Part Number: 43201-0E010
$233.26 MSRP: $334.48
You Save: $101.22 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Highlander | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFXS; 2GRFKS, A25AFXS; AXUH70L-ARXGHA, AXUH70L-ARXMHA, AXUH70L-ARXNHA, AXUH78L-ARXGHA, AXUH78L-ARXMHA, AXUH78L-ARXNHA, GSU70L-ARZGHA, GSU70L-ARZMHA, GSU70L-ARZNHA, GSU70L-ARZSHA, GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA, GSU75L-ARZSHA
View related parts
Toyota Highlander Knuckle, Steering, RH
Part Number: 43211-48010
$327.92 MSRP: $470.21
You Save: $142.29 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Passenger Side
- Replaced by: 43211-0E010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2013 Toyota Highlander | Grande, Limited, Sport, STD | 4 Cyl 2.7L, 6 Cyl 3.3L, 6 Cyl 3.5L | 1ARFE, 2GRFE, 2GRFXE, 3MZFE; 1ARFE, 2GRFE, 2GRFXE, 3MZFE; ASU40L-BRTNKA, GSU40L-BRAGKA, GSU40L-BRAMKA, GSU40L-BRANKA, GSU40L-BRASKA, GSU45L-BRAGKA, GSU45L-BRAMKA, GSU45L-BRANKA, GSU45L-BRASKA, GVU48L-BRXGKA, GVU48L-BRXNKA, MHU48L-BRXMKA, MHU48L-BRXNKA
View related parts
Toyota Highlander Knuckle, Steering, RH
Part Number: 43211-28120
$285.35 MSRP: $409.17
You Save: $123.82 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2004 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 2AZFE, 3MZFE; 1MZFE, 2AZFE, 3MZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA, MCU20L-BWPNKA, MCU23L-BRANKA, MCU23L-BWANKA, MCU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA

Toyota Highlander Steering Knuckle

If you are in demand for superior quality and affordable OEM Toyota Highlander Steering Knuckle, then shop with us! We own a wide range of the reduced-priced genuine Toyota Highlander Steering Knuckle. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Highlander Steering Knuckle Parts Questions & Experts Answers

Knuckle, Steering, LH
43212-28100
Q: How to remove and install the driveaxle and steering knuckle on Toyota Highlander?
A: Before having the drive axle out, the drive axle hub nut and the wheel lug nuts must be loosened and the vehicle has to be raised and supported properly on jack stands before the wheel can be removed. Next it is necessary to loosen the wheel speed sensor from the knuckle and then remove the brake disc from the hub. While maintaining the bolts in position tighten them enough to free the strut from the steering knuckle arm but do not remove the bolts; unscrew the tie-rod end from the steering knuckle arm. Unscrew the Ball Joint-to-lower arml bolt and nuts to relieve the ball joint from the lower arm, pry the Control Arm with a pry bar to separate it from the ball joint. Here it is possible to unscrew the strut-to-knuckle bolts and to shift the drive axle away from the hub; it is recommended to thread a piece of wire over the end of the axle to keep it in place. Disconnect the steering knuckle from the strut, in case you have to eliminate the ball joint from the steering knuckle. For installation, position the knuckle and hub assembly to the right place and align the drive axle to the hub. Force the knuckle into the inner part of the strut flange, put on the bolts and nuts, but do not over tighten them at this stage. Place the nut ont the ball joint and bolt in the control arm then tighten it but halfway through in order to fix it. Connect the tie-rod to the steering knuckle arm and then torque the strut bolt nuts, ball joint to control arm bolt and nuts, and the tie-rod nut to the prescribed torque and replace all cotter-pin with new ones. Put the brake disc in the hub and tighten the caliper and the wheel speed sensor. Last, torque the drive axle/hub nut, final torque to be done once the vehicle is in the ground, then fit the wheels with the lug nuts, lower the vehicle ,and finally torque the lug nuts to the required torque. It is therefore necessary to fit the drive axle/hub nut in place, torque it to the necessary measure, and go on to staking the nut.