How to replace the CV Boot on Toyota Sequoia?

Remove the CV boot. Disassembly: Mount the driveaxle in a vise with wood lined jaws. Check the CV joint for excessive play in the radial direction. Check for smooth operation throughout the full range of motion for each CV joint. If a boot is torn, disassemble the joint, clean the components and inspect for damage. Using a pair of pliers, squeeze the retaining tabs of the large inboard joint boot clamp and slide it away from the CV joint. Using a pair of side cutters cut the boot clamps. Mark the inboard joint to the shaft. Using a pair of snap-ring pliers, expand the snap-ring that connects the outboard joint shaft to the inboard joint and separate the shafts. If you haven't already cut them off, remove both boots. Wrap the splines on the inner end the axleshaft with electrical or duct tape to protect the boots from the sharp edges of the splines. Check: Thoroughly clean all components, including the outer CV joint assembly, with solvent until the old CV joint grease is completely removed. Inspect all visible bearing surfaces for cracks, pitting, scoring and other signs of wear. Reassembly: Slide the clamps and boot(s) onto the axleshaft. Pack the outboard and inboard joint assemblies and boots with grease. Align the matchmarks and place the inboard joint on the shaft, then using a pair of snap-ring pliers, expand the snap-ring and seat the joint on the shaft. Slide the boot into place, making sure both ends seat in their grooves. Adjust the length of the driveaxle. Equalize the pressure in the boot, then tighten and secure the boot clamps. Install the driveaxle assembly.

Why are driveaxle boots important on Toyota Sequoia?

First of all, CV boots are vital but oil and grease can cause the boot material to deteriorate, you should clean the boots with soap and water to prevent further damage. Inspect the boots for tears and cracks.

Genuine Toyota Sequoia CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 CV Boots found

View related parts
Toyota Sequoia Front Cv Joint Boot, Left
Part Number: 04438-0C010
$29.79 MSRP: $41.64
You Save: $11.85 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Drive Shaft Inboard Joint, Lh; Boot, Boot Kit, Inner Boot, Outer Boot
- Position: Front Driver Side
- Replaces: 04437-0C010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Front Cv Joint Boot Kit
Part Number: 04427-0C020
$38.10 MSRP: $53.26
You Save: $15.16 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Drive Shaft; Boot Kit, Outer Boot
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK65L-GKALKA, UCK65L-GKASKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Front Cv Joint Boot Kit Inboard Joint
Part Number: 04437-0C020
$23.92 MSRP: $33.43
You Save: $9.51 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Drive Shaft Inboard Joint; Boot Kit, Inner Boot
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK65L-GKALKA, UCK65L-GKASKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Rear Cv Joint Boot Kit, In Outboard Joint, Left
Part Number: 04429-0C010
$28.91 MSRP: $40.40
You Save: $11.49 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Rear Drive Shaft, In & Outboard Joint, Lh; Boot Kit
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Front Cv Joint Boot, Right
Part Number: 04437-0C010
$29.79 MSRP: $41.64
You Save: $11.85 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Drive Shaft Inboard Joint, Rh
- Position: Passenger Side
- Replaced by: 04438-0C010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Rear Cv Joint Boot Kit, Inboard Joint, Left
Part Number: 04439-0C010
$28.91 MSRP: $40.40
You Save: $11.49 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Rear Drive Shaft Inboard Joint, Lh; Inner Boot
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Front Cv Joint Boot Kit, In Outboard, Right
Part Number: 04438-0C020
$47.55 MSRP: $66.46
You Save: $18.91 (29%)
Product Specifications
- Other Name: Boot Kit, Front Drive Shaft, In & Outboard, Rh; Boot, Boot Kit, Inner Boot, Outer Boot
- Position: Front Passenger Side
- Replaces: 04427-0C010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA

Toyota Sequoia CV Boot

The CV Boot found in Toyota Sequoia model is vital since it shields the Constant Velocity (CV) Joint that transmits power from the transaxle to the wheels. Several types of CV Joints that can be found in Sequoia vehicles are fixed joint embedded at the external ends of the axle, while the plunging joint is placed at the inner part of the axle. This is a boot designated to enclose the CV Joint and shield it from damages from dirt while keeping the joint adequately lubricated. It is recommended to take regular inspections of the CV Boot because the damage to the CV Boot often leads to CV Joint failure and in turn produces popping or clicking noise especially during turns, clunking and feels like vibration during acceleration.

If you are in demand for superior quality and affordable OEM Toyota Sequoia CV Boot, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sequoia CV Boot. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sequoia CV Boot Parts Questions & Experts Answers

Rear Cv Joint Boot Kit, In Outboard Joint, Left
04429-0C010
Q: How to replace the CV Boot on Toyota Sequoia?
A: Remove the CV boot. Disassembly: Mount the driveaxle in a vise with wood lined jaws. Check the CV joint for excessive play in the radial direction. Check for smooth operation throughout the full range of motion for each CV joint. If a boot is torn, disassemble the joint, clean the components and inspect for damage. Using a pair of pliers, squeeze the retaining tabs of the large inboard joint boot clamp and slide it away from the CV joint. Using a pair of side cutters cut the boot clamps. Mark the inboard joint to the shaft. Using a pair of snap-ring pliers, expand the snap-ring that connects the outboard joint shaft to the inboard joint and separate the shafts. If you haven't already cut them off, remove both boots. Wrap the splines on the inner end the axleshaft with electrical or duct tape to protect the boots from the sharp edges of the splines. Check: Thoroughly clean all components, including the outer CV joint assembly, with solvent until the old CV joint grease is completely removed. Inspect all visible bearing surfaces for cracks, pitting, scoring and other signs of wear. Reassembly: Slide the clamps and boot(s) onto the axleshaft. Pack the outboard and inboard joint assemblies and boots with grease. Align the matchmarks and place the inboard joint on the shaft, then using a pair of snap-ring pliers, expand the snap-ring and seat the joint on the shaft. Slide the boot into place, making sure both ends seat in their grooves. Adjust the length of the driveaxle. Equalize the pressure in the boot, then tighten and secure the boot clamps. Install the driveaxle assembly.
Rear Cv Joint Boot Kit, In Outboard Joint, Left
04429-0C010
Q: Why are driveaxle boots important on Toyota Sequoia?
A: First of all, CV boots are vital but oil and grease can cause the boot material to deteriorate, you should clean the boots with soap and water to prevent further damage. Inspect the boots for tears and cracks.