How do you remove and install the oil pan in V6 engine on Toyota Sequoia?

On 4WD models, it will be necessary to either remove the front axle/differential assembly or remove the engine from the vehicle in order to remove the oil pan. Begin by disconnecting the cable from the negative terminal of the battery. Raise the front of the vehicle and place it securely on jackstands. Drain the engine oil and remove the splash shield from underneath the engine. Remove the bolts and nuts that secure oil pan No. 2 (the smaller stamped steel pan) to the larger cast aluminum oil pan, which may be stuck due to RTV sealant; tap it loose with a rubber-tipped mallet or carefully cut the sealant with a putty knife and hammer, ensuring not to damage the mating surfaces. Next, remove the two oil pump pickup tube/strainer mounting nuts and the pickup/strainer assembly, followed by the four bolts that attach the flywheel housing cover and the cover itself. Remove the 17 bolts and 2 nuts securing the oil pan to the engine block, along with the 4 stud bolts, and carefully pry the oil pan loose from the engine block, taking care to only pry in the small cutout areas along the side of the pan. For installation, use a scraper to remove all traces of old sealant from the block and oil pan, and clean the mating surfaces with brake system cleaner. Ensure the threaded holes in the block are clean and check the flange of the steel oil pan for distortion around the bolt holes, flattening it if necessary. Inspect the strainer for cracks or blockage, clean it with solvent, and install it using a new gasket, tightening the fasteners to the specific torque. Apply a 1/8 inch bead of RTV sealant to the upper oil pan flange, position the pan onto the block, and install the fasteners, tightening them to the specific torque in several steps while working from the center out. After installing the aluminum portion of the oil pan, apply a bead of RTV sealant to the flange of the No. 2 oil pan, position it on the upper oil pan, and install the bolts, again tightening them to the specific torque in several steps while working from the center out. Finally, the remainder of installation is the reverse of removal; add oil and install a new filter, then run the engine and check for leaks.

Genuine Toyota Sequoia Oil Pan

Oil Drain Pan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Oil Pans found

View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12102-0S010
$191.96 MSRP: $275.26
You Save: $83.30 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Sub-Assy, Oil, NO.2; Lower Oil Pan, Oil Pan
- Replaces: 12102-38010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Pan, Oil, NO.1
Part Number: 12111-0S011
$254.84 MSRP: $365.42
You Save: $110.58 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Sub-Assy, Oil; Oil Pan, Upper Oil Pan
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12111-0F011
$278.04 MSRP: $398.70
You Save: $120.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan, Upper Oil Pan
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12102-0F020
$212.96 MSRP: $305.38
You Save: $92.42 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Sub-Assy, Oil, NO.2; Lower Oil Pan, Oil Pan
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12111-50112
$217.30 MSRP: $311.60
You Save: $94.30 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan
- Replaces: 12111-50110
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, 2UZFE; UCK35L-GKSLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12102-0F010
$212.96 MSRP: $305.38
You Save: $92.42 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Sub-Assy, Oil, NO.2; Lower Oil Pan, Oil Pan
- Manufacturer Note: (L)
- Replaces: 12102-50111
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12102-50111
$212.96 MSRP: $305.38
You Save: $92.42 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Sub-Assy, Oil, NO.2
- Manufacturer Note: (J)
- Replaced by: 12102-0F010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12111-50110
$217.30 MSRP: $311.60
You Save: $94.30 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: (J)
- Replaced by: 12111-50112
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2005 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12111-0F020
$278.04 MSRP: $398.70
You Save: $120.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan, Upper Oil Pan
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12111-0F010
$272.34 MSRP: $390.53
You Save: $118.19 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan
- Manufacturer Note: (L)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2005 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pan Sub-Assy, Oil
Part Number: 12111-0S010
$211.85 MSRP: $303.77
You Save: $91.92 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan, Upper Oil Pan
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 5.7L | 3URFBE, 3URFE; 3URFBE, 3URFE; USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA

Toyota Sequoia Oil Pan

If you are in demand for superior quality and affordable OEM Toyota Sequoia Oil Pan, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sequoia Oil Pan. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sequoia Oil Pan Parts Questions & Experts Answers

Pan Sub-Assy, Oil
12102-0S010
Q: How do you remove and install the oil pan in V6 engine on Toyota Sequoia?
A: On 4WD models, it will be necessary to either remove the front axle/differential assembly or remove the engine from the vehicle in order to remove the oil pan. Begin by disconnecting the cable from the negative terminal of the battery. Raise the front of the vehicle and place it securely on jackstands. Drain the engine oil and remove the splash shield from underneath the engine. Remove the bolts and nuts that secure oil pan No. 2 (the smaller stamped steel pan) to the larger cast aluminum oil pan, which may be stuck due to RTV sealant; tap it loose with a rubber-tipped mallet or carefully cut the sealant with a putty knife and hammer, ensuring not to damage the mating surfaces. Next, remove the two oil pump pickup tube/strainer mounting nuts and the pickup/strainer assembly, followed by the four bolts that attach the flywheel housing cover and the cover itself. Remove the 17 bolts and 2 nuts securing the oil pan to the engine block, along with the 4 stud bolts, and carefully pry the oil pan loose from the engine block, taking care to only pry in the small cutout areas along the side of the pan. For installation, use a scraper to remove all traces of old sealant from the block and oil pan, and clean the mating surfaces with brake system cleaner. Ensure the threaded holes in the block are clean and check the flange of the steel oil pan for distortion around the bolt holes, flattening it if necessary. Inspect the strainer for cracks or blockage, clean it with solvent, and install it using a new gasket, tightening the fasteners to the specific torque. Apply a 1/8 inch bead of RTV sealant to the upper oil pan flange, position the pan onto the block, and install the fasteners, tightening them to the specific torque in several steps while working from the center out. After installing the aluminum portion of the oil pan, apply a bead of RTV sealant to the flange of the No. 2 oil pan, position it on the upper oil pan, and install the bolts, again tightening them to the specific torque in several steps while working from the center out. Finally, the remainder of installation is the reverse of removal; add oil and install a new filter, then run the engine and check for leaks.