How to remove and install a power steering pump on Toyota Sequoia?

Disconnect the cable from the negative terminal of the battery. Remove the engine cover. Raise the front of the vehicle and support it securely on jackstands. Remove the accessory drivebelt or serpentine drivebelt. Remove the right front wheel. Remove the plastic clips from the the rubber seal on the inner fenderwell splash shield, and remove the seal. Remove the drivebelt. Disconnect the electrical connector from the power steering pressure switch. Position a drain pan under the power steering pump. Disconnect the pressure and return hoses from the backside of the pump. Plug the hoses to prevent contaminants from entering. Discard the sealing washers - new ones should be used during installation. Rotate the pump pulley to access the two mounting bolts through the pulley. Remove the pump mounting fasteners and lift the pump out through the wheelwell, taking care not to spill fluid on the painted surfaces. Installation is the reverse of removal. Use new sealing washers on either side of the pressure line fitting. Tighten the pressure line union boll and the pump mounting bolts and nuts. Fill the power steering reservoir with the recommended fluid and bleed the system.

Genuine Toyota Sequoia Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Power Steering Pumps found

View related parts
Toyota Sequoia Pump Assembly, VANE
Part Number: 44310-0C110
$268.56 MSRP: $385.09
You Save: $116.53 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Pump Assy, Vane
Part Number: 44320-0C030
$290.24 MSRP: $416.19
You Save: $125.95 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 44310-0C030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2005 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Pump Assembly, VANE
Part Number: 44310-0C100
$334.98 MSRP: $480.34
You Save: $145.36 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK60L-GKALKA, UCK60L-GKASKA, UCK65L-GKALKA, UCK65L-GKASKA
View related parts
Toyota Sequoia Pump Assembly, VANE
Part Number: 44310-0C030
Product Specifications
- Other Name: Pump Assy, Vane; Power Steering Pump
- Replaces: 44320-0C020, 44320-0C030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA

Toyota Sequoia Power Steering Pump

Power Steering Pump is one of the important components in the steering system of Toyota Sequoia that helps convert engine power to hydraulic power for assisting the turning action of the Steering Wheel. In transferring this hydraulic power to the steering, the pump lessens the force needed to rotate the steering wheel, hence easier handling of the vehicle. Toyota Sequoia power pump steering is normally through the engine crankshaft and is usually coupled to the steering assembly by high pressure hydraulic hoses. These pumps are essential in providing the power help to the driver particularly when in low speeds, or when the car is stationary. Irrespective of the type of Hydraulic, Electric or Electronic power assisted steering, the Power Steering Pump in Toyota Sequoia vehicles enables drivers to steer the vehicles with relativity.

If you are in demand for superior quality and affordable OEM Toyota Sequoia Power Steering Pump, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sequoia Power Steering Pump. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sequoia Power Steering Pump Parts Questions & Experts Answers

Pump Assembly, VANE
44310-0C110
Q: How to remove and install a power steering pump on Toyota Sequoia?
A: Disconnect the cable from the negative terminal of the battery. Remove the engine cover. Raise the front of the vehicle and support it securely on jackstands. Remove the accessory drivebelt or serpentine drivebelt. Remove the right front wheel. Remove the plastic clips from the the rubber seal on the inner fenderwell splash shield, and remove the seal. Remove the drivebelt. Disconnect the electrical connector from the power steering pressure switch. Position a drain pan under the power steering pump. Disconnect the pressure and return hoses from the backside of the pump. Plug the hoses to prevent contaminants from entering. Discard the sealing washers - new ones should be used during installation. Rotate the pump pulley to access the two mounting bolts through the pulley. Remove the pump mounting fasteners and lift the pump out through the wheelwell, taking care not to spill fluid on the painted surfaces. Installation is the reverse of removal. Use new sealing washers on either side of the pressure line fitting. Tighten the pressure line union boll and the pump mounting bolts and nuts. Fill the power steering reservoir with the recommended fluid and bleed the system.