How to check and repack the front wheel bearings and Wheel Hub on 1995 through 2004 Toyota Tacoma?

This procedure is specific to Tacoma and T100 models. For 4Runner and 1996 and later 4WD Tacoma models, the front wheel bearing is permanently sealed and cannot be lubricated. To check and repack the front wheel bearings, start by raising the front of the vehicle and spinning each wheel to check for noise, rolling resistance, and endplay. If there is noticeable movement, the bearings should be checked and repacked with grease or replaced if necessary. Remove the wheel and the disc brake caliper, and on 4WD vehicles, remove the freewheel hub. On 2WD vehicles, use a small chisel and hammer to remove the dust cover, cotter pin, spindle nut-lock, and spindle nut. On 4WD vehicles, use a small chisel and hammer to bend back the tabs on the lock washer and remove the outer locknut, lock washer, inner locknut, and thrust washer. Pull the hub assembly out slightly and then push it back in to disengage the outer wheel bearing. Remove the hub assembly from the spindle and use a screwdriver or seal puller tool to pry out the grease seal. Remove the inner wheel bearing and clean all parts with solvent, inspecting for any damage. Replace any defective bearing races and use high-temperature front wheel bearing grease to pack the bearings. Apply a thin coat of grease to the spindle and place a small quantity of grease inboard of each bearing race inside the hub. Install the grease-packed inner bearing, a new seal, and tap the seal into place with a hammer and block of wood. Carefully place the hub assembly onto the spindle and push the grease-packed outer bearing into position. On 2WD vehicles, install the washer and spindle nut, tightening it slightly and then spinning the hub in a forward direction while tightening to seat the bearings. Loosen the spindle nut, tighten it by hand until snug, and install the nut lock and cotter pin. On 4WD vehicles, install the thrust washer and inner locknut, tightening it while rotating the hub to seat the bearings. Back off the inner locknut, tighten it again, and install the lock washer and outer locknut. Recheck the bearing preload and adjust if necessary. Finally, reinstall the remaining components in reverse order, lightly greasing the internal components of the manual locking hub assembly with chassis grease.

Genuine Toyota Tacoma Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Wheel Hubs found

View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-60201
$164.54 MSRP: $233.93
You Save: $69.39 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh; Front Hub, Hub, Hub Assembly
- Position: Front Driver Side
- Replaces: 43502-60200, 43502-60180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2016 Toyota Tacoma | Base, SR5 | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN245L-CRADKA, GRN245L-CRFDKA, GRN245L-PRADKA, GRN245L-PRFDKA, GRN250L-PRADKA, TRN240L-TRMDKA, TRN240L-TRPDKA, TRN245L-CRMDKA, TRN245L-CRMSKA, TRN245L-CRPDKA, TRN245L-CRTSKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-04040
$203.58 MSRP: $291.92
You Save: $88.34 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh
- Position: Front Driver Side
- Replaced by: 43502-35170
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2004 Toyota Tacoma | DLX, SR5 | 4 Cyl 2.7L, 6 Cyl 3.4L | 3RZFE, 5VZFE; 3RZFE, 5VZFE; RZN161L-TRMDKAB, RZN161L-TRPDKAB, RZN171L-CRMDKAB, RZN171L-CRPDKAB, VZN160L-TRMDKAB, VZN170L-CRMDKAB, VZN170L-CRMGKAB, VZN170L-CRPDKAB, VZN170L-CRPGKAB, VZN170L-PRPDKAB
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-04112
$145.00 MSRP: $206.13
You Save: $61.13 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh; Front Hub, Hub
- Position: Front Driver Side
- Replaces: 43502-35230
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2016 Toyota Tacoma | Base | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN225L-CRFDKA, TRN220L-TRMDKA, TRN220L-TRPDKA, TRN225L-CRMDKA, TRN225L-CRPDKA, TRN225L-PRPDKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-35170
$203.58 MSRP: $291.92
You Save: $88.34 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh; Front Hub, Hub Assembly
- Position: Front Passenger Side
- Replaces: 43502-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2004 Toyota Tacoma | DLX, SR5 | 4 Cyl 2.7L, 6 Cyl 3.4L | 3RZFE, 5VZFE; 3RZFE, 5VZFE; RZN161L-TRMDKAB, RZN161L-TRPDKAB, RZN171L-CRMDKAB, RZN171L-CRPDKAB, VZN160L-TRMDKAB, VZN170L-CRMDKAB, VZN170L-CRMGKAB, VZN170L-CRPDKAB, VZN170L-CRPGKAB, VZN170L-PRPDKAB
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-04080
$164.54 MSRP: $233.93
You Save: $69.39 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh; Front Hub, Hub
- Position: Front Passenger Side
- Replaces: 43502-04120
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2015-2022 Toyota Tacoma | Base, Limited, SR5 | 4 Cyl 2.7L, 6 Cyl 3.5L | 2GRFKS, 2TRFE; 2GRFKS, 2TRFE; GRN305L-CRFSHA, GRN305L-CRTSHA, GRN305L-PRFSHA, GRN305L-PRTLHA, GRN305L-PRTSHA, GRN310L-PRTLHA, GRN310L-PRTSHA, TRN245L-CRMDKA, TRN245L-CRMSKA, TRN245L-CRPDKA, TRN245L-CRTSKA
- 2005-2010 Toyota Tacoma | Base | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN245L-CRADKA, GRN245L-CRFDKA, GRN245L-PRADKA, GRN245L-PRFDKA, GRN250L-PRADKA, TRN240L-TRMDKA, TRN245L-CRMDKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-09010
$153.64 MSRP: $218.43
You Save: $64.79 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh; Front Hub, Hub
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2003 Toyota Tacoma | DLX | 4 Cyl 2.4L, 6 Cyl 3.4L | 2RZFE, 5VZFE; 2RZFE, 5VZFE; RZN140L-TRMDKAB, RZN140L-TRPDKAB, RZN140L-TRSDKAB, RZN150L-CRMDKAB, RZN150L-CRPDKAB, RZN150L-CRSDKAB, VZN150L-CRMDKAB, VZN150L-CRSDKAB
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-35160
$206.90 MSRP: $296.68
You Save: $89.78 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh; Front Hub, Hub Assembly
- Manufacturer Note: (J)
- Position: Front Driver Side
- Replaces: 43502-04030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2001 Toyota Tacoma | DLX | 4 Cyl 2.7L, 6 Cyl 3.4L | 3RZFE, 5VZFE; 3RZFE, 5VZFE; RZN161L-TRMDKAB, RZN161L-TRPDKAB, RZN171L-CRMDKAB, RZN171L-CRPDKAB, VZN160L-TRMDKAB, VZN170L-CRMDKAB, VZN170L-CRPDKAB, VZN170L-PRPDKAB
View related parts
Toyota Tacoma Rear Axle Bearing And Hub Assembly, Right
Part Number: 42450-04010
$346.36 MSRP: $496.66
You Save: $150.30 (31%)
ADD TO CART
Product Specifications
- Other Name: Hub & Bearing Assy, Rear Axle, Rh; Bearing Housing, Hub & Bearing, Rear Hub & Bearing
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2022 Toyota Tacoma | Base, Limited, SR5 | 4 Cyl 2.7L, 6 Cyl 3.5L, 6 Cyl 4.0L | 1GRFE, 2GRFKS, 2TRFE; 1GRFE, 2GRFKS, 2TRFE; GRN225L-CRFDKA, GRN245L-CRADKA, GRN245L-CRFDKA, GRN245L-PRADKA, GRN245L-PRFDKA, GRN250L-PRADKA, GRN265L-CRADKA, GRN265L-CRFDKA, GRN265L-PRADKA, GRN270L-PRADKA, GRN305L-CRFSHA, GRN305L-CRTSHA, GRN305L-PRFSHA, GRN305L-PRTLHA, GRN305L-PRTSHA, GRN310L-PRTLHA, GRN310L-PRTSHA, GRN325L-CRTSHA, GRN325L-PRTLHA, GRN325L-PRTSHA, GRN330L-PRTLHA, GRN330L-PRTSHA, TRN220L-TRMDKA, TRN220L-TRPDKA, TRN225L-CRMDKA, TRN225L-CRPDKA, TRN225L-PRPDKA, TRN240L-TRMDKA, TRN240L-TRPDKA, TRN245L-CRMDKA, TRN245L-CRMSKA, TRN245L-CRPDKA, TRN245L-CRTSKA, TRN260L-TRMDKA, TRN265L-CRMDKA, TRN265L-CRPDKA, TRN265L-CRTSKA, TRN265L-PRPDKA, TRN265L-PRTSKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-04140
$176.19 MSRP: $252.66
You Save: $76.47 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh; Front Hub, Hub, Wheel Hub
- Position: Front Passenger Side
- Replaces: 43502-04130
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2022 Toyota Tacoma | Base, Limited, SR5 | 4 Cyl 2.7L, 6 Cyl 3.5L, 6 Cyl 4.0L | 1GRFE, 2GRFKS, 2TRFE; 1GRFE, 2GRFKS, 2TRFE; GRN265L-CRADKA, 2TRFE; GRN325L-CRTSHA, GRN265L-CRFDKA, GRN265L-PRADKA, GRN270L-PRADKA, GRN325L-PRTLHA, GRN325L-PRTSHA, GRN330L-PRTLHA, GRN330L-PRTSHA, TRN260L-TRMDKA, TRN265L-CRMDKA, TRN265L-CRPDKA, TRN265L-CRTSKA, TRN265L-PRPDKA, TRN265L-PRTSKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-09020
$199.69 MSRP: $286.35
You Save: $86.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh; Front Hub, Hub
- Manufacturer Note: W(ABS)
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2004 Toyota Tacoma | DLX | 4 Cyl 2.4L, 6 Cyl 3.4L | 2RZFE, 5VZFE; 2RZFE, 5VZFE; RZN140L-TRMDKAB, RZN140L-TRPDKAB, RZN140L-TRSDKAB, RZN150L-CRMDKAB, RZN150L-CRPDKAB, RZN150L-CRSDKAB, VZN150L-CRMDKAB, VZN150L-CRSDKAB
View related parts
Toyota Tacoma Rear Axle Bearing And Hub Assembly, Left
Part Number: 42460-04010
$346.36 MSRP: $496.66
You Save: $150.30 (31%)
ADD TO CART
Product Specifications
- Other Name: Hub & Bearing Assy, Rear Axle, Lh; Bearing Housing, Hub & Bearing, Rear Hub & Bearing
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2022 Toyota Tacoma | Base, Limited, SR5 | 4 Cyl 2.7L, 6 Cyl 3.5L, 6 Cyl 4.0L | 1GRFE, 2GRFKS, 2TRFE; 1GRFE, 2GRFKS, 2TRFE; GRN225L-CRFDKA, GRN245L-CRADKA, GRN245L-CRFDKA, GRN245L-PRADKA, GRN245L-PRFDKA, GRN250L-PRADKA, GRN265L-CRADKA, GRN265L-CRFDKA, GRN265L-PRADKA, GRN270L-PRADKA, GRN305L-CRFSHA, GRN305L-CRTSHA, GRN305L-PRFSHA, GRN305L-PRTLHA, GRN305L-PRTSHA, GRN310L-PRTLHA, GRN310L-PRTSHA, GRN325L-CRTSHA, GRN325L-PRTLHA, GRN325L-PRTSHA, GRN330L-PRTLHA, GRN330L-PRTSHA, TRN220L-TRMDKA, TRN220L-TRPDKA, TRN225L-CRMDKA, TRN225L-CRPDKA, TRN225L-PRPDKA, TRN240L-TRMDKA, TRN240L-TRPDKA, TRN245L-CRMDKA, TRN245L-CRMSKA, TRN245L-CRPDKA, TRN245L-CRTSKA, TRN260L-TRMDKA, TRN265L-CRMDKA, TRN265L-CRPDKA, TRN265L-CRTSKA, TRN265L-PRPDKA, TRN265L-PRTSKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-04120
$164.54 MSRP: $233.93
You Save: $69.39 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh
- Position: Front Passenger Side
- Replaced by: 43502-04080
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2010 Toyota Tacoma | Base | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN245L-CRADKA, GRN245L-CRFDKA, GRN245L-PRADKA, GRN245L-PRFDKA, GRN250L-PRADKA, TRN240L-TRMDKA, TRN245L-CRMDKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-04050
$221.55 MSRP: $317.68
You Save: $96.13 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh
- Position: Front Driver Side
- Replaced by: 43502-35110
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2004 Toyota Tacoma | DLX | 4 Cyl 2.7L, 6 Cyl 3.4L | 3RZFE, 5VZFE; 3RZFE, 5VZFE; RZN191L-TRPDKAB, RZN196L-CRPDKAB, RZN196L-PRPDKAB, VZN195L-CRPDKAB, VZN195L-PRPDKAB
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-04130
$176.19 MSRP: $252.66
You Save: $76.47 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh
- Position: Front Passenger Side
- Replaced by: 43502-04140
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2016 Toyota Tacoma | Base, SR5 | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN265L-CRADKA, GRN265L-CRFDKA, GRN265L-PRADKA, GRN270L-PRADKA, TRN260L-TRMDKA, TRN265L-CRMDKA, TRN265L-CRPDKA, TRN265L-CRTSKA, TRN265L-PRPDKA, TRN265L-PRTSKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-04030
$206.90 MSRP: $296.68
You Save: $89.78 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh
- Manufacturer Note: (L)
- Position: Front Driver Side
- Replaced by: 43502-35160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2001 Toyota Tacoma | DLX | 4 Cyl 2.7L, 6 Cyl 3.4L | 3RZFE, 5VZFE; 3RZFE, 5VZFE; RZN161L-TRMDKAB, RZN161L-TRPDKAB, RZN171L-CRMDKAB, RZN171L-CRPDKAB, VZN160L-TRMDKAB, VZN170L-CRMDKAB, VZN170L-CRPDKAB, VZN170L-PRPDKAB
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Right
Part Number: 43502-60200
$164.54 MSRP: $233.93
You Save: $69.39 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Rh
- Position: Front Passenger Side
- Replaced by: 43502-60201
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2011 Toyota Tacoma | Base | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN245L-CRADKA, GRN245L-CRFDKA, GRN245L-PRADKA, GRN245L-PRFDKA, GRN250L-PRADKA, TRN240L-TRMDKA, TRN240L-TRPDKA, TRN245L-CRMDKA, TRN245L-CRPDKA
View related parts
Toyota Tacoma Front Axle Hub Sub-Assembly, Left
Part Number: 43502-35230
$145.00 MSRP: $206.13
You Save: $61.13 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assy, Front Axle, Lh
- Position: Front Driver Side
- Replaced by: 43502-04112
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2011 Toyota Tacoma | Base | 4 Cyl 2.7L, 6 Cyl 4.0L | 1GRFE, 2TRFE; 1GRFE, 2TRFE; GRN225L-CRFDKA, TRN220L-TRMDKA, TRN220L-TRPDKA, TRN225L-CRMDKA, TRN225L-CRPDKA

Toyota Tacoma Wheel Hub

The Wheel Hub Assembly commonly known as WHA in Toyota Tacoma is an important part through which the wheels of a car revolve and at the same time fixed to the car properly. Specially, the splined teeth are applied to drive configurations and the roller bearings are applied to non-drive wheels to make sure the prime performance of vehicles. The right fixture and the correct torque to be applied is critical in avoiding mechanical breakdowns; SKF Wheel hub bearings were among the most frequently sold bearings in the market. The changes in layouts such as unit assemblies with ABS sensors and non-driven axle hubs with roller bearings are made in order to accommodate various vehicles, thus explaining the necessity of preserving wheel bearings for safety and efficacy.

If you are in demand for superior quality and affordable OEM Toyota Tacoma Wheel Hub, then shop with us! We own a wide range of the reduced-priced genuine Toyota Tacoma Wheel Hub. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Tacoma Wheel Hub Parts Questions & Experts Answers

Front Axle Hub Sub-Assembly, Left
43502-04040
Q: How to check and repack the front wheel bearings and Wheel Hub on 1995 through 2004 Toyota Tacoma?
A: This procedure is specific to Tacoma and T100 models. For 4Runner and 1996 and later 4WD Tacoma models, the front wheel bearing is permanently sealed and cannot be lubricated. To check and repack the front wheel bearings, start by raising the front of the vehicle and spinning each wheel to check for noise, rolling resistance, and endplay. If there is noticeable movement, the bearings should be checked and repacked with grease or replaced if necessary. Remove the wheel and the disc brake caliper, and on 4WD vehicles, remove the freewheel hub. On 2WD vehicles, use a small chisel and hammer to remove the dust cover, cotter pin, spindle nut-lock, and spindle nut. On 4WD vehicles, use a small chisel and hammer to bend back the tabs on the lock washer and remove the outer locknut, lock washer, inner locknut, and thrust washer. Pull the hub assembly out slightly and then push it back in to disengage the outer wheel bearing. Remove the hub assembly from the spindle and use a screwdriver or seal puller tool to pry out the grease seal. Remove the inner wheel bearing and clean all parts with solvent, inspecting for any damage. Replace any defective bearing races and use high-temperature front wheel bearing grease to pack the bearings. Apply a thin coat of grease to the spindle and place a small quantity of grease inboard of each bearing race inside the hub. Install the grease-packed inner bearing, a new seal, and tap the seal into place with a hammer and block of wood. Carefully place the hub assembly onto the spindle and push the grease-packed outer bearing into position. On 2WD vehicles, install the washer and spindle nut, tightening it slightly and then spinning the hub in a forward direction while tightening to seat the bearings. Loosen the spindle nut, tighten it by hand until snug, and install the nut lock and cotter pin. On 4WD vehicles, install the thrust washer and inner locknut, tightening it while rotating the hub to seat the bearings. Back off the inner locknut, tighten it again, and install the lock washer and outer locknut. Recheck the bearing preload and adjust if necessary. Finally, reinstall the remaining components in reverse order, lightly greasing the internal components of the manual locking hub assembly with chassis grease.