Toyota 90084-98027 Bulb

You can Select Your Vehicle to check if 90084-98027 fits your vehicle.

The park/turn signal lights and side marker lights are components of the headlight housing and are located directly behind the housing, although it may be tough to reach. If necessary, it is not very difficult to take off the headlight housing for better access to the bulb. To remove the bulb, first, twist the bulb holder in anti-clockwise direction and pulling the bulb out of it and then pulling the holder also out. Sometimes side marker light is an individual lamp located in the car fender and can be removed only from the bottom. The rear taillight, brake light, turn signal and side marker bulbs are located at the back of car and to take them out, panels in the trunk interior have to be removed. That means bulbs can be removed just by turning the bulb holders anti clockwise. Backup lights located in the trunk lid will involve using a screwdriver to open a cover inside the trunk lid to expose the bulb holder that will be twisted anti-clockwise to be removed. For the center high-mounted stop light, the screw is located at the trunk with the lid open since it requires a hand to reach under the rear package shelf to rotate and for the removal of the bulb holder. These are located in the instrument cluster that involves the replacement of the bulbs by unplugging the instrument cluster. The interior light entails removing the lens by twisting it and then unscrewing the bulb from the terminals, all this while being considerate to the glass because of its fragility. For the license plate light, one has to remove the trunk lid lock cylinder, and thereafter outside trim panel to reveal the license light bezel which is pulled towards the left to be completely removed. Finally for the fog light, the car must be lifted and supported on jackstands, then the splash shield must be disconnected and the bulb holder twisted from the housing before the bulb can be changed.

Open the hood and reach behind the headlight assembly to unplug the electrical connector by depressing the clip on the harness connector. To access the left-side headlight bulbs, remove the battery, then take out the pushpin securing the air intake duct and set the duct aside. Grasp the bulb holder securely and rotate it counterclockwise to remove it from the housing, disconnecting the electrical connector before pulling the holder out. Pull straight out on the bulb to remove it from the bulb holder, and without touching the glass with bare fingers, insert the new bulb assembly into the headlight housing. Finally, plug in the electrical connector.

The park/turn signal lights and side marker lights are integrated into the headlight housing, with access to the bulbs available from behind, though it may be challenging. For left-side bulbs, removing the battery may help. To replace a bulb, rotate the bulb holder counterclockwise and pull it out, then remove the bulb from the holder. In some models, the side marker light is a separate unit located in the front fender, requiring access from underneath after partially removing the inner fender splash shield. The process for installation follows the reverse order of removal. The taillight, brake, turn signal, and side marker bulbs can be accessed by removing panels in the cargo area; similarly, rotate the bulb holders counterclockwise to remove the bulbs, with installation reversing the removal steps. For the center high-mounted stop light, open the liftgate, remove the pushpins securing the bottom cover, take out the screws, lower the bulb housing, twist the bulb holder counterclockwise to remove it, and pull the bulb straight out. The installation follows the reverse order. The front overhead interior light can be removed as an assembly using a pry tool, with the bulb pulling straight out from between the terminals, and installation is the reverse. For the license plate light, use a plastic trim tool or taped screwdriver to remove the access cover on the liftgate's interior side, then remove the bulb holders and replace the bulbs, with installation reversing the removal. To replace the fog light, raise the vehicle and secure it on jackstands, remove the lower engine splash shield, twist the bulb holder from the housing, and replace the bulb, with installation following the reverse order.

For installation, plug in the electrical connector that was disconnected earlier to complete the installation of the headlight bulb.

Open the hood and reach behind the headlight assembly to unplug the electrical connector. Note: If you're removing the left-side headlight, remove the fresh-air intake duct.

Unplug the electrical connector from the bulb and holder assembly by pushing in on the center of the clip and then pulling down on the headlight bulb electrical connector.

For installation, plug in the electrical connector that was disconnected earlier to complete the installation of the headlight bulb.

Turn the front turn signal bulb socket counterclockwise and pull it out of the headlight housing.

Disengage the bulb retaining spring and swing it out of the way.

1. Open the hood and disconnect the electrical connector to the bulb. 2. Turn the bulb holder counterclockwise and remove it from the headlight housing. 3. Pull the bulb straight out to remove it from the bulb holder. 4. Installation is the reverse of removal. When installing the retaining screw, press straight down until it clicks in place.

If equipped, pull the rubber watershield off the bulb assembly.