Make sure this part fits

Toyota 47201-14560 Brake Master Cylinder Sub-Assembly

1986-1991 Toyota Supra 4720114560

Customer Questions & Expert Answers (2)
Toyota 47201-14560 Brake Master Cylinder Sub-Assembly
  • Part Description
    Cylinder Sub-Assy, Brake Master
  • Part Name Code
    47201
  • Replaced By
    47201-14730
  • Manufacturer
    Toyota
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Toyota
    Part Name Code47201
    Manufacturer Part Number47201-14560
    Part DescriptionCylinder Sub-Assy, Brake Master
    Item Dimensions9.2 x 7.3 x 5.7 inches
    Item Weight4.20 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerToyota
    SKU47201-14560
    WarrantyThis genuine Toyota part is guaranteed by Toyota's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Trim & Engine Important vehicle option details
    1986-1991 Toyota Supra6 Cyl 3.0L7MGE, 7MGTE; 7MGE, 7MGTE; MA70L-BJMVFA, MA70L-BJMVFK, MA70L-BJMVZA, MA70L-BJMVZK, MA70L-BJPVFA, MA70L-BJPVFK, MA70L-BJPVZA, MA70L-BJPVZK, MA70L-BLMVFA, MA70L-BLMVFK, MA70L-BLMVZA, MA70L-BLMVZK, MA70L-BLPVFA, MA70L-BLPVFK, MA70L-BLPVZA, MA70L-BLPVZK
  • Customer Questions & Expert Answers

    Q:
    Is the above part number correct or is there another correct number for my car? Posted by ToyotaPartsDeal Specialist
    A:
    You can Select Your Vehicle to check if 47201-14560 fits your vehicle.
    Posted by ToyotaPartsDeal Specialist
    Q:
    How to overhaul a master cylinder on Toyota Supra? Posted by Customer
    A:
    Before overhauling the Brake Master Cylinder, it is important to check the availability and cost of a new or factory-rebuilt unit, as well as the availability of a rebuild kit. To remove the Brake Master Cylinder, start by removing as much fluid as possible from the reservoir. Place rags under the line fittings and prepare caps or plastic bags to cover the ends of the lines once they are disconnected. Loosen the tube nuts at the ends of the brake lines using a flare-nut wrench. Pull the brake lines away from the Brake Master Cylinder slightly and plug the ends to prevent contamination. Disconnect the electrical connector and remove the four nuts attaching the Brake Master Cylinder to the power booster. Lift the Brake Master Cylinder out of the engine compartment, being careful not to spill any fluid. To overhaul the Brake Master Cylinder, obtain the proper rebuild kit and inspect the reservoir grommet for leakage. Remove the reservoir and depress the pistons using a wooden dowel. Remove the stop bolt, outlet plugs, and copper gaskets. Carefully remove the snap-ring and then remove the internal components from the cylinder bore. Inspect the bore for any damage. Replace all parts included in the rebuild kit, following the instructions provided. Lubricate all parts with clean brake fluid during assembly. Push the assembled components into the bore and install the stop bolt and snap ring. Before installing a new or rebuilt Brake Master Cylinder, it should be bench bled. Mount the Brake Master Cylinder in a vise and insert threaded plugs into the brake line outlet holes. Fill the reservoir with brake fluid and push the piston assembly into the Brake Master Cylinder bore to expel air. Repeat the procedure until only brake fluid is expelled from the brake line outlet holes. Alternatively, you can use your finger to cover the hole and prevent air from being drawn back into the Brake Master Cylinder. Install the Brake Master Cylinder over the studs on the power brake booster and tighten the mounting nuts. Thread the brake line fittings into the Brake Master Cylinder and completely tighten them. Fill the Brake Master Cylinder reservoir with fluid and bleed the Brake Master Cylinder and brake system if necessary. Test the operation of the brake system before using the vehicle normally.
    Posted by ToyotaPartsDeal Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Toyota Part 47201-14560, the Right Choice

To ensure reliability, purchase Toyota part # 47201-14560 Brake Master Cylinder Sub-Assembly. It is sometimes referred to as Toyota Brake Master Cylinder, Toyota Master Cylinder Repair Kit. For unrivaled quality, OEM parts are the ultimate choice. These parts are manufactured by Toyota's official factory using top-quality materials and undergo strict testing procedures, ensuring outstanding dependability and long-lasting durability. This part fits 1986-1991 Toyota Supra.

ToyotaPartsDeal.com is a leading supplier of genuine Toyota parts and accessories such as Toyota 4720114560 Brake Master Cylinder Sub-Assembly. In need of OEM Toyota parts? Look no further than our extensive inventory of genuine Toyota parts, competitively priced to be highly exceptional in the market. They are all manufacturer-warrantied. Add to that, our easy return policy and swift delivery service, and your shopping experience promises to be the great pleasant ever. For detailed Toyota parts information, click here.

Why choose Toyota Parts Deal

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly