Make sure this part fits

Toyota 43403-35030 Joint Assembly, Front Axle Inboard

1996-2002 Toyota 4Runner 4340335030

Customer Questions & Expert Answers (2)
Toyota 43403-35030 Joint Assembly, Front Axle Inboard
  • Part Description
    Joint Set, Front Axle I ; Joint Assembly, Front Drive Inboard, Lh
  • Position
    Front
  • Manufacturer
    Toyota
Make sure this part fits
$334.96 MSRP: $480.32
You Save: $145.36 (31%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Toyota
    Manufacturer Part Number43403-35030
    Part DescriptionJoint Set, Front Axle I ; Joint Assembly, Front Drive Inboard, Lh
    Other NamesInner CV Joint, Inner Joint Assembly
    Item Dimensions9.8 x 5.2 x 5.4 inches
    Item Weight8.80 Pounds
    PositionFront
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerToyota
    SKU43403-35030
    WarrantyThis genuine Toyota part is guaranteed by Toyota's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Trim & Engine Important vehicle option details
    1996-2002 Toyota 4RunnerLULI, SR5B, SR5V|4 Cyl 2.7L, 6 Cyl 3.4L3RZFE, 5VZFE; 3RZFE, 5VZFE; RZN185L-GKMSKA, RZN185L-GKPSKA, VZN185L-GKMGKA, VZN185L-GKPGKA, VZN185L-GKPSKA, VZN185L-GKPZKA
  • Customer Questions & Expert Answers

    Q:
    Is the above part number correct or is there another correct number for my car? Posted by ToyotaPartsDeal Specialist
    A:
    You can Select Your Vehicle to check if 43403-35030 fits your vehicle.
    Posted by ToyotaPartsDeal Specialist
    Q:
    What are the steps and considerations for overhauling CV joints and boots on 1996 through 2002 Toyota 4Runner? Posted by Customer
    A:
    If the CV joints have to be replaced, one should consider all viable possibilities before starting the task, as rebuilt CV boot sets are available on an exchange basis, which will prove beneficial in the long run. In either case, compare the cost and whereabouts of the respective spares before dismantling the car, and do not dismantle the outboard CV joint. Mount the CV boot in a vice with the wood-lined jaws and this is to avoid damaging the axle in the process for it will be easy to check if the CV joint is moving excessively to and from that is flexible of smooth operation when subjected to force. If a particular boot is damaged it should be dissembled by unzipping the joint area where the fabric is ripped and then the parts should be cleaned to check for further damages. With a small screwdriver, you should pull the retaining tabs of the clamps; To do it, pry up the outer boot of your hard drive and take it off. Draw the inner CV joint boot back and remove the housing from the tripod while noting the position of the tripod and the axleshaft for proper assembly. The snap-ring which secures the tripod joint is to be taken out by snap-ring pliers, now use a hammer and a brass punch tool while applying care not to harm the bearing surfaces of the tripod joint to be dismounted from the CV boot. If not already done, remove both boots and apply protection to the splines at the internal end of the axleshaft using some type of tape. Remove all the components which are soaked in solvent to check the surfaces of bearings for wearing; in case of wear on the inner CV joint, the new joint can be put on the old axleshaft, but in the case of wear on the outer joint, the new outer joint and the axleshaft are needed. To break down, first you have to slide off the clamps and the boot over the axleshaft; next place the tripod over the shaft; apply grease and then the tripod into its housing and pack grease around it. Adjust the position of the boot, center the driveshaft stump on the axle, pump the boot to the same pressure, put the boot band into position before securing the driveshaft and the new assembly.
    Posted by ToyotaPartsDeal Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Toyota Part 43403-35030, the Right Choice

To ensure reliability, purchase Toyota part # 43403-35030 Joint Assembly, Front Axle Inboard. It is sometimes referred to as Toyota CV Joint. For unrivaled quality, OEM parts are the ultimate choice. These parts are manufactured by Toyota's official factory using top-quality materials and undergo strict testing procedures, ensuring outstanding dependability and long-lasting durability. This part fits 1996-2002 Toyota 4Runner.

ToyotaPartsDeal.com is a leading supplier of genuine Toyota parts and accessories such as Toyota 4340335030 Joint Assembly, Front Axle Inboard. In need of OEM Toyota parts? Look no further than our extensive inventory of genuine Toyota parts, competitively priced to be highly exceptional in the market. They are all manufacturer-warrantied. Add to that, our easy return policy and swift delivery service, and your shopping experience promises to be the great pleasant ever. For detailed Toyota parts information, click here.

Why choose Toyota Parts Deal

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly