Toyota 84870-08010 Switch Assy, Outer Mirror

You can Select Your Vehicle to check if 84870-08010 fits your vehicle.

To source the hazard warning switch, first of all, it is required to disassemble the center trim side finish panel of the instrument panel. Carefully twist the clips to release the switch housing and unsnap it from the switch, remove the tab connector on the back of the switch. Removal or Installation is basically the opposite of the other; it entails the act of putting in something or a method used in fastening of items. With regard to the power mirror control switch, starting with the removal of the fuse box cover, the electrical connector should also be removed before pushing the switch out of the panel. Similar to the case with removal, installation is also the opposite of removal. These finishes comprise the HVAC controls, defogger switch assembly, and the designs that are fixed on the instrument panel; they must be detached cautiously so that their links with the center cluster finish panel can be severed. Pop off the clips of the HVAC control assembly and remove electrical connectors at the back of switch without straining the wire harnesses. In installation, it happens in a reverse order, that is, the last thing that has been installed must be the first thing to be removed. To dismantle this system, one is required to pry the switch for the instrument panels rheostats and disconnect the electrical connector for the switch for the removal of the switch, the procedure of fitting in is the reverse of the removal process. These include the console switches and power outlet switches and the procedure involves; gently removing the switch panel from the instrument panel, remove the electrical connector and push the switch out of the panel while the putting in of the switch entails the reverse process. Regarding the power outlet, it is done in the similar sequential manner however after reaching for the power outlet remove the electrical connector then push the outlet through the panel and the process of installation will be as follows but in the reverse order. All in all, for the engine start/stop switch in Smart Key models, the instructions are as follows: Disconnected the cable from the negative terminal, denounced the heater and air conditioning control assembly, denounced the engine switch wiring harness connectors, pull the two retaining clips back and extract the switch out from the control assembly, for installation, reverse the steps stated above.

To check the hazard warning switch, it must first be removed from the center dashboard trim bezel, followed by testing for continuity between the terminals; if it fails, replacement is necessary. For replacement, carefully pry the upper cluster finish panel from the dashboard, then pull the panel out to disconnect the electrical connector at the rear of the switch, ensuring to squeeze the clips retaining the hazard switch. The power mirror control switch, located at the left end of the instrument panel, should be removed for testing continuity between its terminals; if continuity is not as specified, it should be replaced. To replace it, carefully pry the switch from the panel using tape on the screwdriver tip to avoid scratches, disconnect the electrical connector, and reinstall by reversing the removal procedure. The traction control switch, which works with the ABS braking system, should be removed for testing; continuity should be present when pressed and absent when released, with replacement required if it does not meet these conditions. For replacement, pry the switch from the panel, disconnect the electrical connector, and reinstall by reversing the removal procedure. The instrument panel light control switch, a rheostat controlling voltage to the lights, requires removal for testing; apply battery voltage to terminal 1 and a ground jumper to terminal 3, checking for varying voltage as the knob is turned. For replacement, on models with the rheostat below the left vent, pry the switch panel out of the dashboard with a screwdriver, ensuring to tape the tip to prevent scratches, while models with a thumb-wheel require the instrument cluster to be removed for access.

Disconnect the cable from the negative terminal of the battery, then disable the airbag system. Remove the instrument cluster trim panel, and push the power mirror switch out from the backside of the panel before unplugging the electrical connector from the switch, with installation being the reverse of removal. For the instrument panel illumination rheostat, push the switch out from the backside of the panel, unplug the electrical connector, and again, installation is the reverse of removal. For the vehicle skid control and power rear window switch, carefully pry the switch panel from the instrument panel, disconnect the electrical connector(s) from the switch(es), and carefully pry the switch(es) from the switch panel, with installation following the reverse order of removal.

Carefully pry the switch(es) from the switch panel.