How to disconnect the negative cable from the battery and remove the center console, shift lever assembly, and shift cables on Toyota Camry?

Disconnect the negative cable from the battery. Raise the front of the vehicle and place it securely on jackstands. Remove the center console. Remove the center console mounting bracket fasteners and bracket. Remove the floor shift lever assembly mounting fasteners and lift the shift lever assembly up. Remove the clips and washers that attach the shift and select cables to the shift lever. Remove the large clip-type cable retainers that attach the cables to the bracket at the forward end of the shift lever base. Remove the center airbag sensor mounting bolts and move the sensor to the side. Caution: Do not disconnect the electrical connector or allow the sensor to be hit or dropped. From inside of the engine compartment, remove the retaining clips and washers from the cable ends at the transaxle. Remove the large clips and washers that retain the shift and select cables to the bracket on the transaxle. Remove the bolts that attach the cable retainer to the firewall. Remove the outer retainer and grommet. Remove the inner retainer and grommet from the firewall. Pull the cable(s) out through the firewall. Installation is the reverse of removal. When attaching cables to the front of the shifter assembly, the wider part of the cable end flange should face Up. When attaching the shift cable ends to the shifter with the clips and washers, the toothed edge of the cable eyes should face Up.

How to adjust the shift cable on Toyota Camry?

When adjusting the shift lever inside the vehicle, ensure that it moves smoothly and accurately to each position and that the shift indicator displays the correct gear position. If the indicator is misaligned, follow these steps: Remove the battery and battery tray. Remove the nut connecting the shift cable to the manual lever on the transaxle. Move the shift lever to the Neutral position and ensure the manual lever on the transaxle is also in Neutral. On certain models, move the manual lever into Park and then back two clicks into Neutral. On other models, verify alignment between the switch body and switch hub. Slide the boot back from the end of the cable and move the slider towards the end of the cable, lifting the lock upwards. Install the cable to the manual lever, tighten the nut securely, and push the lock down to secure the slider piece. Check the operation of the transaxle in each shift lever position and readjust the cable if necessary. Slide the boot cover back over the adjuster assembly. For replacement, disconnect the cable from the manual lever and remove the C-clip cable retainer from the bracket above the manual lever. Remove the center console and the bolts from the cable housing retainer on the floor inside the vehicle. Pry off the cable end from the shift housing and disconnect the cable eye from the shift lever pin. Pull the cable through the floor and then reverse the removal steps for installation. Adjust the cable.

Genuine Toyota Camry Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

92 Shift Cables found

View related parts
Toyota Camry Cable Assembly, Parking Lock
Part Number: 33880-06011
$52.93 MSRP: $73.99
You Save: $21.06 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Parking Lock (For Floor Shift)
- Comment: (FOR FLOOR SHIFT)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE, XLE | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 2AZFE, 3MZFE; 1MZFE, 2AZFE, 3MZFE; ACV30L-CEAGKA, ACV30L-CEANKA, ACV30L-CEASKA, ACV30L-CEPGKA, ACV30L-CEPNKA, ACV30L-CEPSKA, MCV30L-CEAGKA, MCV30L-CEANKA, MCV30L-CEASKA, MCV30L-CEPGKA, MCV30L-CEPNKA, MCV30L-CEPSKA, MCV31L-CEASKA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06080
$192.08 MSRP: $275.43
You Save: $83.35 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 33820-06081
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2001 Toyota Camry | CE, LE, XLE | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-CEPDKK, MCV20L-CEPGKA, MCV20L-CEPGKK, MCV20L-CEPNKA, MCV20L-CEPNKK
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06070
$192.08 MSRP: $275.43
You Save: $83.35 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 33820-06071
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2001 Toyota Camry | CE, LE, XLE | 4 Cyl 2.2L | 5SFE; 5SFE; SXV20L-CEPDKA, SXV20L-CEPDKK, SXV20L-CEPGKA, SXV20L-CEPNKA, SXV20L-CEPNKK
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-33130
$192.66 MSRP: $276.26
You Save: $83.60 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2001 Toyota Camry | CE, LE, XLE | 4 Cyl 2.2L | 5SFE, 5SFNE; 5SFE, 5SFNE; SXV20L-AEPDKK, SXV20L-AEPGKA, SXV20L-AEPNKA, SXV20L-AEPNKK, SXV23L-AEPNCA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06270
$218.53 MSRP: $313.35
You Save: $94.82 (31%)
ADD TO CART
Product Specifications
- Replaces: 33820-33270
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2010 Toyota Camry | LE, SE, XLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV40L-AEAGKA, 2AZFE; ACV40L-CEAGKA, ACV40L-AEANKA, ACV40L-CEANKA, ACV40L-CEASKA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06071
$192.08 MSRP: $275.43
You Save: $83.35 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 33820-06070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2001 Toyota Camry | CE, LE, XLE | 4 Cyl 2.2L | 5SFE; 5SFE; SXV20L-CEPDKA, SXV20L-CEPDKK, SXV20L-CEPGKA, SXV20L-CEPNKA, SXV20L-CEPNKK
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06130
$192.55 MSRP: $276.09
You Save: $83.54 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE, XLE | 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 3MZFE; 1MZFE, 3MZFE; MCV30L-CEAGKA, MCV30L-CEANKA, MCV30L-CEASKA, MCV30L-CEPGKA, MCV30L-CEPNKA, MCV30L-CEPSKA, MCV31L-CEASKA
View related parts
Toyota Camry Cable Transmission Control Shift
Part Number: 33821-33170
$221.08 MSRP: $317.03
You Save: $95.95 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Transmission Control Shift (For Floor Shift); Shift Control Cable
- Comment: (FOR FLOOR SHIFT)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-AEMNKA, ACV30L-AEMSKA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-33280
$428.60 MSRP: $630.90
You Save: $202.30 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2010 Toyota Camry | LE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV40L-AEMNKA
View related parts
Toyota Camry Cable Assembly, TRANSMIS
Part Number: 33820-06520
$197.88 MSRP: $283.75
You Save: $85.87 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Control Cable, Shift Control Cable
- Replaces: 33820-33400
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2022 Toyota Camry | LE, No Grade, SE, XLE, XSE | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFKS; 2GRFKS, A25AFKS; AXVA70L-AEZNBA, A25AFKS; AXVA70L-CEZEBA, AXVA70L-AEZSBA, AXVA70L-CEZGBA, AXVA70L-CEZNBA, AXVA70L-CEZPBA, AXVA70L-CEZSBA, GSV70L-CEZGBA, GSV70L-CEZPBA
View related parts
Toyota Camry CABLE ASSY, TRANSMIS
Part Number: 33820-06710
$193.24 MSRP: $277.09
You Save: $83.85 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2022 Toyota Camry
View related parts
Toyota Camry Cable Transmission Control Select
Part Number: 33822-32121
$127.05 MSRP: $180.62
You Save: $53.57 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Transmission Control Select (For Floor Shift)
- Comment: (FOR FLOOR SHIFT)
- Replaced by: 33822-32123
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1989 Toyota Camry | DX | 4 Cyl 2.0L | 3SFE; 3SFE; SV25L-UEMDKA, SV25L-UEMDKK
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06260
$192.55 MSRP: $276.09
You Save: $83.54 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 33820-33180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2011 Toyota Camry | LE, SE, XLE | 4 Cyl 2.5L, 6 Cyl 3.5L | 2ARFE, 2GRFE; 2ARFE, 2GRFE; ASV40L-AETGKA, 2GRFE; ASV40L-CETGKA, ASV40L-AETNKA, ASV40L-CETNKA, ASV40L-CETSKA, GSV40L-AETGKA, GSV40L-AETNKA, GSV40L-CETGKA, GSV40L-CETNKA, GSV40L-CETSKA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06370
$220.62 MSRP: $316.36
You Save: $95.74 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shift Control Cable
- Replaces: 33820-33290
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2011 Toyota Camry | 4 Cyl 2.4L | 2AZFXE; 2AZFXE; AHV40L-AEXGBA, 2AZFXE; AHV40L-CEXGBA
View related parts
Toyota Camry Cable Assembly, TRANSMIS
Part Number: 33820-06490
$155.36 MSRP: $220.88
You Save: $65.52 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Transmission Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2017 Toyota Camry | LE, N, SE, XLE, XSE | 4 Cyl 2.5L | 2ARFE; 2ARFE; ASV50L-CETEKA, ASV50L-CETGKA, ASV50L-CETNKA, ASV50L-CETPKA, ASV50L-CETSKA
View related parts
Toyota Camry Cable Assembly, TRANSMIS
Part Number: 33820-06381
$427.69 MSRP: $629.57
You Save: $201.88 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Transmission Control
- Replaced by: 33820-06382
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2011 Toyota Camry | LE, SE | 4 Cyl 2.5L | 2ARFE; 2ARFE; ASV40L-CEFNKA, ASV40L-CEFSKA
View related parts
Toyota Camry Cable Assembly, TRANSMIS
Part Number: 33820-06382
$427.69 MSRP: $629.57
You Save: $201.88 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy, Transmission Control
- Replaces: 33820-06381
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2011 Toyota Camry | LE, SE | 4 Cyl 2.5L | 2ARFE; 2ARFE; ASV40L-CEFNKA, ASV40L-CEFSKA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-06280
$429.84 MSRP: $632.72
You Save: $202.88 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shift Control Cable
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2010 Toyota Camry | LE, SE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV40L-CEMNKA, ACV40L-CEMSKA
View related parts
Toyota Camry Cable Assy, Transmission Control
Part Number: 33820-32181
$128.40 MSRP: $184.42
You Save: $56.02 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988 Toyota Camry | DX, LE | 4 Cyl 2.5L | 2VZFE; 2VZFE; VZV21L-UEMDKA, VZV21L-UEMNKA, VZV21L-UEMNKK
View related parts
Toyota Camry Cable Transmission Control Shift
Part Number: 33821-32181
Product Specifications
- Other Name: Cable Transmission Control Shift (For Floor Shift)
- Comment: (FOR FLOOR SHIFT)
- Replaced by: 33821-32183
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1989 Toyota Camry | DX, LE | 4 Cyl 2.5L | 2VZFE; 2VZFE; VZV21L-UEMDKA, VZV21L-UEMNKK

| Page 1 of 5 |Next >

1-20 of 92 Results

Toyota Camry Shift Cable

If you are in demand for superior quality and affordable OEM Toyota Camry Shift Cable, then shop with us! We own a wide range of the reduced-priced genuine Toyota Camry Shift Cable. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Camry Shift Cable Parts Questions & Experts Answers

Cable Assy, Transmission Control
33820-06270
Q: How to disconnect the negative cable from the battery and remove the center console, shift lever assembly, and shift cables on Toyota Camry?
A: Disconnect the negative cable from the battery. Raise the front of the vehicle and place it securely on jackstands. Remove the center console. Remove the center console mounting bracket fasteners and bracket. Remove the floor shift lever assembly mounting fasteners and lift the shift lever assembly up. Remove the clips and washers that attach the shift and select cables to the shift lever. Remove the large clip-type cable retainers that attach the cables to the bracket at the forward end of the shift lever base. Remove the center airbag sensor mounting bolts and move the sensor to the side. Caution: Do not disconnect the electrical connector or allow the sensor to be hit or dropped. From inside of the engine compartment, remove the retaining clips and washers from the cable ends at the transaxle. Remove the large clips and washers that retain the shift and select cables to the bracket on the transaxle. Remove the bolts that attach the cable retainer to the firewall. Remove the outer retainer and grommet. Remove the inner retainer and grommet from the firewall. Pull the cable(s) out through the firewall. Installation is the reverse of removal. When attaching cables to the front of the shifter assembly, the wider part of the cable end flange should face Up. When attaching the shift cable ends to the shifter with the clips and washers, the toothed edge of the cable eyes should face Up.
Cable Assy, Transmission Control
33820-06270
Q: How to adjust the shift cable on Toyota Camry?
A: When adjusting the shift lever inside the vehicle, ensure that it moves smoothly and accurately to each position and that the shift indicator displays the correct gear position. If the indicator is misaligned, follow these steps: Remove the battery and battery tray. Remove the nut connecting the shift cable to the manual lever on the transaxle. Move the shift lever to the Neutral position and ensure the manual lever on the transaxle is also in Neutral. On certain models, move the manual lever into Park and then back two clicks into Neutral. On other models, verify alignment between the switch body and switch hub. Slide the boot back from the end of the cable and move the slider towards the end of the cable, lifting the lock upwards. Install the cable to the manual lever, tighten the nut securely, and push the lock down to secure the slider piece. Check the operation of the transaxle in each shift lever position and readjust the cable if necessary. Slide the boot cover back over the adjuster assembly. For replacement, disconnect the cable from the manual lever and remove the C-clip cable retainer from the bracket above the manual lever. Remove the center console and the bolts from the cable housing retainer on the floor inside the vehicle. Pry off the cable end from the shift housing and disconnect the cable eye from the shift lever pin. Pull the cable through the floor and then reverse the removal steps for installation. Adjust the cable.