How to inspect and replace brake hoses and lines on Toyota Celica?

About every six months, with the vehicle raised and securely supported on jackstands, inspect the rubber hoses connecting the steel brake lines to the front and rear brake assemblies for cracks, chafing, leaks, blisters, and other damage, as these are crucial parts of the brake system. Use a light and mirror for a thorough check, and replace any damaged hose with a new one. To replace the front brake hose, loosen the wheel lug nuts, raise the vehicle, and remove the wheel. At the frame bracket, hold the hose fitting with an open-end wrench and unscrew the brake line fitting from the hose, using a flare-nut wrench to avoid rounding off the corners. Remove the U-clip and E-ring, if equipped, from the female fitting at the bracket with pliers, then pass the hose through the bracket. At the caliper end, remove the banjo fitting bolt and separate the hose from the caliper, ensuring to replace the two copper sealing washers during installation. Remove the U-clip from the strut bracket and feed the hose through. To install the new hose, pass the caliper fitting end through the strut bracket, connect it to the caliper with the banjo bolt and copper washers, ensuring the locating lug is engaged, then tighten the bolt to the specified torque. Push the metal support into the strut bracket and install the U-clip, ensuring the hose isn't twisted. Route the hose into the frame bracket, connect the brake line fitting by hand, install the clip and E-ring if equipped, and tighten securely. Bleed the caliper, install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts to the specified torque. For the rear brake hose, repeat the removal and installation steps, ensuring to bleed the wheel cylinder or caliper. When replacing metal brake lines, use the correct parts, avoiding copper tubing, and purchase steel brake lines from a dealer or auto parts store. Prefabricated brake lines with flared tube ends and installed fittings are available and should be securely supported in brackets with adequate clearance from moving or hot components. After installation, check the master cylinder fluid level, add fluid as necessary, bleed the brake system, and test the brakes carefully before driving.

Genuine Toyota Celica Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

131 Brake Lines found

View related parts
Toyota Celica Hose, Flexible
Part Number: 96940-32605
$47.67 MSRP: $66.63
You Save: $18.96 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Brake Tube)
- Replaces: 96940-32605-86, 96940-31265, 96940-30265
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | Supra | 4 Cyl 2.7L | 4ME; 4ME; MA46L-BLMQEA
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02C25
$51.38 MSRP: $71.83
You Save: $20.45 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear RH); Brake Hose, Flex Hose
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2005 Toyota Celica | 4 Cyl 1.8L | 1ZZFE; 1ZZFE; ZZT230L-BLMSHA, ZZT230L-BLPSHA
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02424
$36.22 MSRP: $50.63
You Save: $14.41 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible, NO.1(For Front)
- Comment: (FOR FRONT)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1982-1985 Toyota Celica | Supra | 6 Cyl 2.8L | 5MGE; 5MGE; MA61L-BLMQFA, MA61L-BLMQFK, MA61L-BLPQFA, MA61L-BLPQFK
View related parts
Toyota Celica Hose, Flexible
Part Number: 96950-39955
$47.67 MSRP: $66.63
You Save: $18.96 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear Brake Tube, NO.2)
- Comment: (FOR REAR BRAKE TUBE, NO.2)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1982-1985 Toyota Celica | GTS, Supra | 4 Cyl 2.4L, 6 Cyl 2.8L | 22REC, 5MGE; 22REC, 5MGE; MA61L-BLMQFA, MA61L-BLMQFK, MA61L-BLPQFA, MA61L-BLPQFK, RA65L-BCMQEA, RA65L-BCMQEK, RA65L-BCPQEA, RA65L-BKMQEA, RA65L-BKPQEA, RA65L-BLMQEA, RA65L-BLMQEK, RA65L-BLPQEA
View related parts
Toyota Celica Hose, Flexible
Part Number: 96960-39955
$47.67 MSRP: $66.63
You Save: $18.96 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible, NO.2(For Front); Hose
- Comment: (FOR FRONT)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1982-1985 Toyota Celica | Supra | 6 Cyl 2.8L | 5MGE; 5MGE; MA61L-BLMQFA, MA61L-BLMQFK, MA61L-BLPQFA, MA61L-BLPQFK
View related parts
Toyota Celica Tube, Front Brake
Part Number: 47323-14050
$8.27 MSRP: $11.68
You Save: $3.41 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Front Brake, NO.8
- Position: Front
- Replaced by: 47323-14052
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | GT, LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 4ME; 20R, 22R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA, RA43L-BCMQSA
View related parts
Toyota Celica Tube, Front Brake
Part Number: 47323-14051
$8.27 MSRP: $11.68
You Save: $3.41 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Front Brake, NO.8
- Position: Front
- Replaced by: 47323-14052
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1981 Toyota Celica | GT | 4 Cyl 2.4L | 22R; 22R; RA43L-BCMQSA
View related parts
Toyota Celica Tube, Rear Brake
Part Number: 47324-14071
$8.33 MSRP: $11.76
You Save: $3.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Rear Brake, NO.4
- Position: Rear
- Replaced by: 47324-14072
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1981 Toyota Celica | GT | 4 Cyl 2.4L | 22R; 22R; RA43L-BCMQSA
View related parts
Toyota Celica Tube, Rear Brake
Part Number: 47321-20280
$62.25 MSRP: $87.75
You Save: $25.50 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Rear Brake, NO.1
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota Celica | GT, GTS, ST | 4 Cyl 1.6L, 4 Cyl 2.2L | 4AFE, 5SFE; 4AFE, 5SFE; AT180L-BCMSKA, AT180L-BCMSKK, AT180L-BCPSKA, AT180L-BCPSKK, ST184L-BCMGKA, ST184L-BCMGKK, ST184L-BCPGKA, ST184L-BCPGKK, ST184L-BKMGKA, ST184L-BKPGKA, ST184L-BLMGKA, ST184L-BLMGKK, ST184L-BLMVKA, ST184L-BLMVKK, ST184L-BLPGKA, ST184L-BLPGKK, ST184L-BLPVKA, ST184L-BLPVKK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02550
$62.58 MSRP: $88.21
You Save: $25.63 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible, NO.1(For Front)
- Comment: (FOR FRONT)
- Replaced by: 90947-02940
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota Celica | GT, GTS, ST, Turbo 4WD, Turbo All Trac | 4 Cyl 2.0L | 3SFE, 3SGELC, 3SGTE; 3SFE, 3SGELC, 3SGTE; ST162L-BCMSKA, ST162L-BCMSKK, ST162L-BCMVFA, ST162L-BCMVFK, ST162L-BCMVKA, ST162L-BCMVKK, ST162L-BCPSKA, ST162L-BCPSKK, ST162L-BCPVFA, ST162L-BCPVKA, ST162L-BCPVKK, ST162L-BKMVKA, ST162L-BKPVKA, ST162L-BLMVFA, ST162L-BLMVFK, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK, ST165L-BLMVZA, ST165L-BLMVZK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02473
$65.24 MSRP: $91.97
You Save: $26.73 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear LH)
- Replaced by: 90947-02941
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1986-1987 Toyota Celica | GTS | 4 Cyl 2.0L | 3SGELC; 3SGELC; ST162L-BCMVFA, ST162L-BCMVFK, ST162L-BCPVFA, ST162L-BLMVFA, ST162L-BLMVFK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02551
$65.24 MSRP: $91.97
You Save: $26.73 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear LH)
- Replaced by: 90947-02941
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota Celica | GTS | 4 Cyl 2.0L | 3SGELC; 3SGELC; ST162L-BCMVFA, ST162L-BCMVFK, ST162L-BCPVFA, ST162L-BLMVFA, ST162L-BLMVFK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02548
$67.92 MSRP: $95.74
You Save: $27.82 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear LH)
- Replaced by: 90947-02472
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota Celica | GT, ST | 4 Cyl 2.0L | 3SFE; 3SFE; ST162L-BCMSKA, ST162L-BCMSKK, ST162L-BCMVKA, ST162L-BCMVKK, ST162L-BCPSKA, ST162L-BCPSKK, ST162L-BCPVKA, ST162L-BCPVKK, ST162L-BKMVKA, ST162L-BKPVKA, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02596
$69.28 MSRP: $97.66
You Save: $28.38 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear RH)
- Replaced by: 90947-02982
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota Celica | Turbo 4WD, Turbo All Trac | 4 Cyl 2.0L | 3SGTE; 3SGTE; ST185L-BLMVZA, ST185L-BLMVZK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02769
$77.96 MSRP: $109.90
You Save: $31.94 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear Brake Tube)
- Comment: (FOR REAR BRAKE TUBE)
- Replaced by: 90947-02852
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1996 Toyota Celica | GT | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BCMGKA, ST204L-BCMGKK, ST204L-BCPGKA, ST204L-BCPGKK, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLPGKA, ST204L-BLPGKK
View related parts
Toyota Celica Hose, Flexible
Part Number: 90947-02852
$77.96 MSRP: $109.90
You Save: $31.94 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Flexible(For Rear Brake Tube); Brake Hose, Flex Hose
- Comment: (FOR REAR BRAKE TUBE)
- Replaces: 90947-02769
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BCMGKA, ST204L-BCMGKK, ST204L-BCMSKA, ST204L-BCPGKA, ST204L-BCPGKK, ST204L-BCPSKA, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPGKK, ST204L-BLPSKA
View related parts
Toyota Celica Tube, Rear Brake
Part Number: 47324-20210
$5.34 MSRP: $7.47
You Save: $2.13 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Rear Brake, NO.4
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2005 Toyota Celica | 4 Cyl 1.8L | 1ZZFE; 1ZZFE; ZZT230L-BLMSHA, ZZT230L-BLPSHA
View related parts
Toyota Celica Tube, Front Brake
Part Number: 47311-14170
$6.02 MSRP: $8.42
You Save: $2.40 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Front Brake, NO.1
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | GT, LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 4ME; 20R, 22R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA, RA43L-BCMQSA
View related parts
Toyota Celica Tube, Front Brake
Part Number: 47313-20890
$7.58 MSRP: $10.60
You Save: $3.02 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Front Brake, NO.3
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2005 Toyota Celica | 4 Cyl 1.8L | 1ZZFE, 2ZZGE; 1ZZFE, 2ZZGE; ZZT230L-BLMSHA, ZZT230L-BLPSHA, ZZT231L-BLFVFA, ZZT231L-BLPVFA
View related parts
Toyota Celica Tube, Front Brake
Part Number: 47311-14130
$7.66 MSRP: $10.72
You Save: $3.06 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Front Brake, NO.1
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1978-1981 Toyota Celica | GT, LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 4ME; 20R, 22R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA, RA43L-BCMQSA

| Page 1 of 7 |Next >

1-20 of 131 Results

Toyota Celica Brake Line

If you are in demand for superior quality and affordable OEM Toyota Celica Brake Line, then shop with us! We own a wide range of the reduced-priced genuine Toyota Celica Brake Line. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Celica Brake Line Parts Questions & Experts Answers

Hose, Flexible
90947-02598
Q: How to inspect and replace brake hoses and lines on Toyota Celica?
A: About every six months, with the vehicle raised and securely supported on jackstands, inspect the rubber hoses connecting the steel brake lines to the front and rear brake assemblies for cracks, chafing, leaks, blisters, and other damage, as these are crucial parts of the brake system. Use a light and mirror for a thorough check, and replace any damaged hose with a new one. To replace the front brake hose, loosen the wheel lug nuts, raise the vehicle, and remove the wheel. At the frame bracket, hold the hose fitting with an open-end wrench and unscrew the brake line fitting from the hose, using a flare-nut wrench to avoid rounding off the corners. Remove the U-clip and E-ring, if equipped, from the female fitting at the bracket with pliers, then pass the hose through the bracket. At the caliper end, remove the banjo fitting bolt and separate the hose from the caliper, ensuring to replace the two copper sealing washers during installation. Remove the U-clip from the strut bracket and feed the hose through. To install the new hose, pass the caliper fitting end through the strut bracket, connect it to the caliper with the banjo bolt and copper washers, ensuring the locating lug is engaged, then tighten the bolt to the specified torque. Push the metal support into the strut bracket and install the U-clip, ensuring the hose isn't twisted. Route the hose into the frame bracket, connect the brake line fitting by hand, install the clip and E-ring if equipped, and tighten securely. Bleed the caliper, install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts to the specified torque. For the rear brake hose, repeat the removal and installation steps, ensuring to bleed the Wheel Cylinder or caliper. When replacing metal brake lines, use the correct parts, avoiding copper tubing, and purchase steel brake lines from a dealer or auto parts store. Prefabricated brake lines with flared tube ends and installed fittings are available and should be securely supported in brackets with adequate clearance from moving or hot components. After installation, check the master cylinder fluid level, add fluid as necessary, bleed the brake system, and test the brakes carefully before driving.