How to remove and install a front strut on Toyota Highlander?

Loosen the wheel lug nuts, raise the vehicle, and support it securely on jackstands before removing the wheel and supporting the control arm with a floor jack. Disconnect the stabilizer bar link from the strut and remove the brake hose bracket along with the wheel speed sensor wiring harness from the strut. Mark the position of the steering knuckle to the strut to help preserve the camber alignment adjustment, then remove the strut-to-knuckle nuts and knock the bolts out with a hammer and punch. Carefully separate the strut from the steering knuckle, avoiding overextension of the inner CV joint and preventing the steering knuckle from falling outward to avoid damaging the brake hose. If disassembling the strut, loosen the damper shaft nut without removing it. For 2004 and later Lexus models, remove the panels on the cowl to access the top of the struts, and for 2008 and later Highlander models, remove the windshield wiper arms and motor, side seals, and plastic cowl below the wiper motor assembly. For Lexus models equipped with electronic modulated air suspension, remove the shock absorber cap and detach the airline fitting from the top of the strut. Support the strut and spring assembly with one hand or have an assistant hold it while removing the three strut-to-shock tower nuts, then carefully remove the assembly from the fender well, noting that some models have a strut brace that can be removed without taking out the struts. Inspect the strut body for leaking fluid, dents, cracks, and other damage, and check the coil spring for chips or cracks in the coating, as well as the spring seal for cuts and deterioration. If any issues are found, proceed to disassemble the strut, and for Lexus models with modulated air suspension, replace the strut assembly if faulty. To install, guide the strut assembly into the fenderwell, insert the three upper mounting studs through the shock tower holes, and install the nuts to secure the strut. Slide the steering knuckle into the strut flange, insert the two bolts, match the previously marked position of the strut to the steering knuckle, and tighten them to the specified torque. Reattach the brake hose bracket and the wheel speed sensor wiring harness bracket, then install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts to the specified torque. Finally, tighten the three upper mounting nuts to the specified torque and, if applicable, attach the air-line to the top of the strut before installing the cap.

Genuine Toyota Highlander Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

118 Shock Absorbers found

View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-49565
$143.66 MSRP: $205.09
You Save: $61.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assy, Shock, Front Rh; Strut, Strut Assembly
- Manufacturer Note: MARK 48510-48110
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.3L | 2AZFE, 3MZFE; 2AZFE, 3MZFE; ACU25L-BRPNKA, ACU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA
View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-8Z103
$133.84 MSRP: $191.00
You Save: $57.16 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly Set, S ; Absorber Assembly, Shock, Front Rh; Strut
- Manufacturer Note: MARK 48510-0E150
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2014-2016 Toyota Highlander | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA
View related parts
Toyota Highlander Shock Absorber Assembly Front Left
Part Number: 48520-8Z167
$128.64 MSRP: $183.58
You Save: $54.94 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly Set, S ; Absorber Assembly, Shock, Front Lh; Strut
- Manufacturer Note: MARK 48520-0E310
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2019 Toyota Highlander | 6 Cyl 3.5L | 2GRFE, 2GRFKS; 2GRFE, 2GRFKS; GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU50L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-B9810
$139.22 MSRP: $198.00
You Save: $58.78 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Set Shock ; Absorber Assembly, Shock, Front Rh; Strut
- Manufacturer Note: MARK 48510-0E120
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2013 Toyota Highlander | Limited, Medium, Sport, STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU40L-ARAGKA, GSU40L-ARAMKA, GSU40L-ARANKA, GSU40L-ARASKA, GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA
View related parts
Toyota Highlander Shock Absorber Assembly Rear Left
Part Number: 48531-0E110
$42.83 MSRP: $59.86
You Save: $17.03 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Rear Lh; Shock, Shock Absorber
- Manufacturer Note: MARK 48531-0E110
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2014-2017 Toyota Highlander | 6 Cyl 3.5L | 2GRFE, 2GRFKS; 2GRFE, 2GRFKS; GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Front Left
Part Number: 48520-8Z013
$129.83 MSRP: $185.28
You Save: $55.45 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Lh; Strut
- Manufacturer Note: MARK 48520-0E150
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2014-2016 Toyota Highlander | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA
View related parts
Toyota Highlander Shock Absorber Assembly Set
Part Number: 48520-8Z288
$126.82 MSRP: $180.51
You Save: $53.69 (30%)
ADD TO CART
Product Specifications
- Other Name: ABSORBER Assembly Set, S; Strut
- Manufacturer Note: MARK 48520-0E350
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Highlander | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Front Left
Part Number: 48520-49735
$143.66 MSRP: $205.09
You Save: $61.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assy, Shock, Front Lh; Strut, Strut Assembly
- Manufacturer Note: MARK 48520-48110
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.3L | 2AZFE, 3MZFE; 2AZFE, 3MZFE; ACU25L-BRPNKA, ACU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA
View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-8Z306
$140.27 MSRP: $200.19
You Save: $59.92 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly Set, S ; Absorber Assembly, Shock, Front Rh; Strut
- Manufacturer Note: MARK 48510-0E310
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2019 Toyota Highlander | 6 Cyl 3.5L | 2GRFE, 2GRFKS; 2GRFE, 2GRFKS; GSU50L-ARTGKA, GSU50L-ARTMKA, GSU50L-ARTNKA, GSU50L-ARZGHA, GSU50L-ARZMHA, GSU50L-ARZNHA, GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Rear Right
Part Number: 48530-49555
$149.40 MSRP: $212.65
You Save: $63.25 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: ABSORBER Assembly, Shock, Rear RH; Strut
- Manufacturer Note: MARK 48530-48230
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.3L | 2AZFE, 3MZFE; 2AZFE, 3MZFE; ACU25L-BRPNKA, ACU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA
View related parts
Toyota Highlander Shock Absorber Assembly Rear Left
Part Number: 48540-49295
$147.99 MSRP: $210.65
You Save: $62.66 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: ABSORBER Assembly, Shock, Rear LH; Strut
- Manufacturer Note: MARK 48540-48230
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.3L | 2AZFE, 3MZFE; 2AZFE, 3MZFE; ACU25L-BRPNKA, ACU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA
View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-49445
$183.96 MSRP: $264.76
You Save: $80.80 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assy, Shock, Front Rh
- Manufacturer Note: MARK 48510-48090
- Position: Front Passenger Side
- Replaced by: 48510-A9360
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.3L | 2AZFE, 3MZFE; 2AZFE, 3MZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, MCU23L-BRANKA, MCU23L-BWANKA
View related parts
Toyota Highlander Shock Absorber Assembly Rear Left
Part Number: 48531-0E290
$43.19 MSRP: $60.36
You Save: $17.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Rear Lh; Shock, Shock Absorber
- Manufacturer Note: MARK 48531-0E290
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2019 Toyota Highlander | 6 Cyl 3.5L | 2GRFE, 2GRFKS; 2GRFE, 2GRFKS; GSU55L-ARTGKA, GSU55L-ARTMKA, GSU55L-ARTNKA, GSU55L-ARZGHA, GSU55L-ARZMHA, GSU55L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Set
Part Number: 48510-8Z437
$126.58 MSRP: $180.18
You Save: $53.60 (30%)
ADD TO CART
Product Specifications
- Other Name: ABSORBER Assembly Set, S; Strut
- Manufacturer Note: MARK 48510-0E350
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Highlander | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GSU75L-ARZGHA, GSU75L-ARZMHA, GSU75L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-80530
$127.57 MSRP: $181.44
You Save: $53.87 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock, Front Rh
- Manufacturer Note: MARK 48510-48330
- Position: Front Passenger Side
- Replaced by: 48510-80615
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2013 Toyota Highlander | Limited, STD | 6 Cyl 3.5L | 2GRFXE; 2GRFXE; GVU48L-BRXGKA, GVU48L-BRXNKA
View related parts
Toyota Highlander Shock Absorber Assembly Set
Part Number: 48510-8Z435
$126.58 MSRP: $180.18
You Save: $53.60 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: ABSORBER Assembly Set, S; Strut
- Manufacturer Note: MARK 48510-0E340
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Highlander | 4 Cyl 2.5L, 6 Cyl 3.5L | 2GRFKS, A25AFXS; 2GRFKS, A25AFXS; AXUH70L-ARXGHA, AXUH70L-ARXMHA, AXUH70L-ARXNHA, AXUH78L-ARXGHA, AXUH78L-ARXMHA, AXUH78L-ARXNHA, GSU70L-ARZGHA, GSU70L-ARZMHA, GSU70L-ARZNHA
View related parts
Toyota Highlander Shock Absorber Assembly Front Left
Part Number: 48520-A9580
$131.09 MSRP: $186.43
You Save: $55.34 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Set, Shock ; Absorber Assembly, Shock, Front Lh; Strut
- Manufacturer Note: MARK 48520-0E120
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2013 Toyota Highlander | Limited, Medium, Sport, STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU40L-ARAGKA, GSU40L-ARAMKA, GSU40L-ARANKA, GSU40L-ARASKA, GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA
View related parts
Toyota Highlander Shock Absorber Assembly Rear Right
Part Number: 48530-A9750
$151.50 MSRP: $216.45
You Save: $64.95 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Set, Shock ; Absorber Assembly, Shock, Rear Rh; Strut
- Manufacturer Note: MARK 48530-0E080
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2013 Toyota Highlander | Limited, Medium, Sport, STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA
View related parts
Toyota Highlander Shock Absorber Assembly Front Right
Part Number: 48510-49285
$146.91 MSRP: $209.25
You Save: $62.34 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assy, Shock, Front Rh
- Position: Front Passenger Side
- Replaced by: 48510-49655
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2004 Toyota Highlander | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.3L | 1MZFE, 2AZFE, 3MZFE; 1MZFE, 2AZFE, 3MZFE; ACU20L-BRPNKA, ACU20L-BWPNKA, ACU25L-BRPNKA, ACU25L-BWPNKA, MCU20L-BWPNKA, MCU23L-BRANKA, MCU23L-BWANKA, MCU25L-BWPNKA, MCU28L-BRANKA, MCU28L-BWANKA
View related parts
Toyota Highlander Shock Absorber Assembly Rear Left
Part Number: 48540-A9400
$144.10 MSRP: $205.86
You Save: $61.76 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Set, Shock ; Absorber Assembly, Shock, Rear Lh; Strut
- Manufacturer Note: MARK 48540-0E080
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2013 Toyota Highlander | Limited, Medium, Sport, STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU45L-ARAGKA, GSU45L-ARAMKA, GSU45L-ARANKA, GSU45L-ARASKA

| Page 1 of 6 |Next >

1-20 of 118 Results

Toyota Highlander Shock Absorber

If you are in demand for superior quality and affordable OEM Toyota Highlander Shock Absorber, then shop with us! We own a wide range of the reduced-priced genuine Toyota Highlander Shock Absorber. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Highlander Shock Absorber Parts Questions & Experts Answers

Shock Absorber Assembly Front Right
48510-49565
Q: How to remove and install a front strut on Toyota Highlander?
A: Loosen the wheel lug nuts, raise the vehicle, and support it securely on jackstands before removing the wheel and supporting the Control Arm with a floor jack. Disconnect the stabilizer bar link from the strut and remove the brake hose bracket along with the wheel speed sensor wiring harness from the strut. Mark the position of the Steering Knuckle to the strut to help preserve the camber alignment adjustment, then remove the strut-to-knuckle nuts and knock the bolts out with a hammer and punch. Carefully separate the strut from the steering knuckle, avoiding overextension of the inner CV joint and preventing the steering knuckle from falling outward to avoid damaging the brake hose. If disassembling the strut, loosen the damper shaft nut without removing it. For 2004 and later Lexus models, remove the panels on the cowl to access the top of the struts, and for 2008 and later Highlander models, remove the windshield wiper arms and motor, side seals, and plastic cowl below the wiper motor assembly. For Lexus models equipped with electronic modulated air suspension, remove the shock absorber cap and detach the airline fitting from the top of the strut. Support the strut and spring assembly with one hand or have an assistant hold it while removing the three strut-to-shock tower nuts, then carefully remove the assembly from the fender well, noting that some models have a strut brace that can be removed without taking out the struts. Inspect the strut body for leaking fluid, dents, cracks, and other damage, and check the coil spring for chips or cracks in the coating, as well as the spring seal for cuts and deterioration. If any issues are found, proceed to disassemble the strut, and for Lexus models with modulated air suspension, replace the strut assembly if faulty. To install, guide the strut assembly into the fenderwell, insert the three upper mounting studs through the shock tower holes, and install the nuts to secure the strut. Slide the steering knuckle into the strut flange, insert the two bolts, match the previously marked position of the strut to the steering knuckle, and tighten them to the specified torque. Reattach the brake hose bracket and the wheel speed sensor wiring harness bracket, then install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts to the specified torque. Finally, tighten the three upper mounting nuts to the specified torque and, if applicable, attach the air-line to the top of the strut before installing the cap.