How to remove, inspect, and install the rocker arm assembly on Toyota Land Cruiser?

Remove the valve cover and tighten the nut by first starting at the front side of the cylinder head and unfasten the rocker arm bolts gradually, as much as possible in the recommended order with the assembly parallel to the plane of the cylinder head. Pull out the rocker arm assembly as a single unit at a time, place the push rods in a paper box with holes to ensure that they do not get clumped together and be cautious of losing any of the components off the rocker shaft. Remove the pushrods from the engine and set them aside in a different place because you may get lost when it is time to re-install them. Inspect all rocker arms for signs of wear, cracks, and other operational damage on the areas where the pushrods and the valve stems touch the faces of the rocker arms while confirming that all the holes at the pushrod end of the rocker arms are open. Checking the pushrod end of each rocker arm for wear, cracks, or galling; should a rocker arm be at all worn or abused, it should be changed, along with its pivot. Check the pushrods for indicative signs of cracks, uneven wear along their strap like lengths, and at both ends, and to check for bending, roll each pushrod on a piece of plate glass. Clean and apply engine oil or moly-base grease on the lower ends of the pushrods and fit them in the corresponding positions, such that each of the pushrod has a proper fit inside the lifter socket. It is also recommended that moly-base grease applied to both the subhead termed, valve stem-ends and the top ends of the pertinent push rods before orienting the rocker arms and fixing the capscrews. Place the rocker arms into position and fit the pivots, bridges and capscrews before applying moly-base grease to the pivots thus protecting the contacting surfaces from being damaged by the pressures always associated with oil before tighter pressures from engine oil are established. Loosen it with a little at a time in the said sequence until the torque gets to the specified value, replace the valve cover, start up the engine, observe for oil leakage and weird sounds from the valve train.

Genuine Toyota Land Cruiser Rocker Arm

Engine Rocker Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Rocker Arms found

View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13801-0P010
$49.28 MSRP: $68.87
You Save: $19.59 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1; Rocker Arms
- Replaces: 13801-23011, 13801-23010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2017 Toyota Land Cruiser | 8 Cyl 5.7L | 3URFE; 3URFE; URJ200L-GNTEKA, URJ200L-GNZVKA
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13801-23011
$49.28 MSRP: $68.87
You Save: $19.59 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Replaced by: 13801-0P010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2017 Toyota Land Cruiser | 8 Cyl 5.7L | 3URFE; 3URFE; URJ200L-GNTEKA, URJ200L-GNZVKA
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13801-60020
$23.55 MSRP: $32.92
You Save: $9.37 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1969-1970 Toyota Land Cruiser | 6 Cyl 3.9L | F; F; FJ40L-A, FJ40LV-A, FJ55LG-
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13802-60020
$25.13 MSRP: $35.12
You Save: $9.99 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.2
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1969-1970 Toyota Land Cruiser | 6 Cyl 3.9L | F; F; FJ40L-A, FJ40LV-A, FJ55LG-
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13811-61030
$29.33 MSRP: $41.00
You Save: $11.67 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1; Rocker Arms
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1993 Toyota Land Cruiser | 6 Cyl 4.0L, 6 Cyl 4.2L | 2F, 3FE; 2F, 3FE; FJ60LG-KA, FJ60LV-KA, FJ62LG-PNEA, FJ62LG-PNEK, FJ62LV-PNEA, FJ80L-GNPNEA
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve
Part Number: 13801-36020
$44.85 MSRP: $62.69
You Save: $17.84 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Replaced by: 13801-0P030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2021 Toyota Land Cruiser | 8 Cyl 5.7L | 3URFE; 3URFE; URJ200L-GNZVKA
View related parts
Toyota Land Cruiser Shaft Sub-Assembly, Valve Rocker
Part Number: 13901-61011
Product Specifications
- Other Name: Shaft Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1981-1985 Toyota Land Cruiser | 6 Cyl 4.2L | 2F; 2F; FJ40L-KJA, FJ40LV-KCJA, FJ40LV-KCJK, FJ60LG-KA
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13801-60021
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1969-1980 Toyota Land Cruiser | 6 Cyl 3.9L, 6 Cyl 4.2L | 2F, F; 2F, F; FJ40L-A, FJ40L-KJA, FJ40L-KJK, FJ40LV-A, FJ40LV-AC, FJ40LV-KCJA, FJ40LV-KCJK, FJ45LP-KK, FJ55LG-, FJ55LG-KA, FJ55LG-KK
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13801-61010
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1980 Toyota Land Cruiser | 6 Cyl 4.2L | 2F; 2F; FJ40L-KJA, FJ40LV-KCJA, FJ40LV-KCJK, FJ45LP-KK, FJ55LG-KA, FJ55LG-KK
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13802-61010
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.2
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1980 Toyota Land Cruiser | 6 Cyl 4.2L | 2F; 2F; FJ40L-KJA, FJ40LV-KCJA, FJ40LV-KCJK, FJ45LP-KK, FJ55LG-KA, FJ55LG-KK
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13811-56030
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1987 Toyota Land Cruiser | 6 Cyl 3.4L | 3B; 3B; BJ70LV-MNK, BJ70LV-MRK
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13812-56030
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.2
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1987 Toyota Land Cruiser | 6 Cyl 3.4L | 3B; 3B; BJ70LV-MNK, BJ70LV-MRK
View related parts
Toyota Land Cruiser Shaft Sub-Assembly, Valve Rocker
Part Number: 13901-56020
Product Specifications
- Other Name: Shaft Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1987 Toyota Land Cruiser | 6 Cyl 3.4L | 3B; 3B; BJ70LV-MNK, BJ70LV-MRK
View related parts
Toyota Land Cruiser Shaft Sub-Assembly, Valve Rocker
Part Number: 13901-60022
Product Specifications
- Other Name: Shaft Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1973-1980 Toyota Land Cruiser | 6 Cyl 3.9L, 6 Cyl 4.2L | 2F, F; 2F, F; FJ40L-A, FJ40L-KJA, FJ40L-KJK, FJ40LV-A, FJ40LV-AC, FJ40LV-KCJA, FJ40LV-KCJK, FJ45LP-KK, FJ55LG-, FJ55LG-KA, FJ55LG-KK
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13812-61021
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.2
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1981-1985 Toyota Land Cruiser | 6 Cyl 4.2L | 2F; 2F; FJ40L-KJA, FJ40LV-KCJA, FJ40LV-KCJK, FJ60LG-KA
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13811-61021
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1981-1985 Toyota Land Cruiser | 6 Cyl 4.2L | 2F; 2F; FJ40L-KJA, FJ40LV-KCJA, FJ40LV-KCJK, FJ60LG-KA
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13802-60021
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.2
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1969-1980 Toyota Land Cruiser | 6 Cyl 3.9L, 6 Cyl 4.2L | 2F, F; 2F, F; FJ40L-A, FJ40L-KJA, FJ40L-KJK, FJ40LV-A, FJ40LV-AC, FJ40LV-KCJA, FJ40LV-KCJK, FJ45LP-KK, FJ55LG-, FJ55LG-KA, FJ55LG-KK
View related parts
Toyota Land Cruiser Arm Sub-Assembly, Valve Rocker
Part Number: 13812-61030
Product Specifications
- Other Name: Arm Sub-Assy, Valve Rocker, NO.2; Rocker Arms
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1993 Toyota Land Cruiser | 6 Cyl 4.0L, 6 Cyl 4.2L | 2F, 3FE; 2F, 3FE; FJ60LG-KA, FJ60LV-KA, FJ62LG-PNEA, FJ62LG-PNEK, FJ62LV-PNEA, FJ80L-GNPNEA
View related parts
Toyota Land Cruiser Shaft Sub-Assembly, Valve Rocker
Part Number: 13901-60021
Product Specifications
- Other Name: Shaft Sub-Assy, Valve Rocker, NO.1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1969-1974 Toyota Land Cruiser | 6 Cyl 3.9L | F; F; FJ40L-A, FJ40LV-A, FJ40LV-AC, FJ55LG-
View related parts
Toyota Land Cruiser Shaft Sub-Assembly, Valve Rocker
Part Number: 13902-60020
Product Specifications
- Other Name: Shaft Sub-Assy, Valve Rocker, NO.2
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1969-1974 Toyota Land Cruiser | 6 Cyl 3.9L | F; F; FJ40L-A, FJ40LV-A, FJ40LV-AC, FJ55LG-

| Page 1 of 2 |Next >

1-20 of 21 Results

Toyota Land Cruiser Rocker Arm

If you are in demand for superior quality and affordable OEM Toyota Land Cruiser Rocker Arm, then shop with us! We own a wide range of the reduced-priced genuine Toyota Land Cruiser Rocker Arm. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Land Cruiser Rocker Arm Parts Questions & Experts Answers

Arm Sub-Assembly, Valve Rocker
13812-56030
Q: How to remove, inspect, and install the rocker arm assembly on Toyota Land Cruiser?
A: Remove the valve cover and tighten the nut by first starting at the front side of the Cylinder Head and unfasten the rocker arm bolts gradually, as much as possible in the recommended order with the assembly parallel to the plane of the cylinder head. Pull out the rocker arm assembly as a single unit at a time, place the push rods in a paper box with holes to ensure that they do not get clumped together and be cautious of losing any of the components off the rocker shaft. Remove the pushrods from the engine and set them aside in a different place because you may get lost when it is time to re-install them. Inspect all rocker arms for signs of wear, cracks, and other operational damage on the areas where the pushrods and the valve stems touch the faces of the rocker arms while confirming that all the holes at the pushrod end of the rocker arms are open. Checking the pushrod end of each rocker arm for wear, cracks, or galling; should a rocker arm be at all worn or abused, it should be changed, along with its pivot. Check the pushrods for indicative signs of cracks, uneven wear along their strap like lengths, and at both ends, and to check for bending, roll each pushrod on a piece of plate glass. Clean and apply engine oil or moly-base grease on the lower ends of the pushrods and fit them in the corresponding positions, such that each of the pushrod has a proper fit inside the lifter socket. It is also recommended that moly-base grease applied to both the subhead termed, valve stem-ends and the top ends of the pertinent push rods before orienting the rocker arms and fixing the capscrews. Place the rocker arms into position and fit the pivots, bridges and capscrews before applying moly-base grease to the pivots thus protecting the contacting surfaces from being damaged by the pressures always associated with oil before tighter pressures from engine oil are established. Loosen it with a little at a time in the said sequence until the torque gets to the specified value, replace the valve cover, start up the engine, observe for oil leakage and weird sounds from the valve train.