How do you remove and install a crankshaft pulley and oil seal on Toyota Prius?

Remove the crankshaft pulley and note how the seal is installed, ensuring the new one is positioned to the same depth and orientation. Carefully pry the oil seal out of the cover using a seal puller or a large screwdriver, taking care not to damage the crankshaft. To facilitate removal, cut the lip of the seal with a utility knife, being cautious not to distort the cover or scratch the crankshaft; wrapping electrician's tape around the screwdriver tip can help prevent damage. Apply clean engine oil or multi-purpose grease to the outer edge of the new seal and install it in the cover with the lip facing inward. Drive the seal into place using a seal driver or a large socket and hammer, ensuring it enters the bore squarely and stops at the correct depth. Check the surface on the pulley hub for any grooves caused by long-term contact with the seal, and replace the pulley if necessary. Lubricate the pulley hub with clean engine oil and reinstall the crankshaft pulley, then install and tighten the retaining bolt. The remainder of the installation follows the reverse order of removal.

Genuine Toyota Prius Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Crankshaft Seals found

View related parts
Toyota Prius Seal, Oil
Part Number: 90311-38089
$11.53 MSRP: $16.12
You Save: $4.59 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Oil(For Timing Gear Case Or Timing Chain Case)
- Replaced by: 90311-A0018
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2012 Toyota Prius | E, G, L, S | 4 Cyl 1.8L | 2ZRFXE; 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA, ZVW35L-BHXEBA, ZVW35L-BHXEBK
View related parts
Toyota Prius Seal
Part Number: 90311-25021
$9.02 MSRP: $12.61
You Save: $3.59 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal(For Oil Pump)
- Comment: (FOR OIL PUMP)
- Replaced by: 90311-25032
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2009 Toyota Prius | 4 Cyl 1.5L | 1NZFXE; 1NZFXE; NHW11L-AEEEBA, NHW11L-AEEEBK, NHW20L-AHEEBA, NHW20L-AHEEBK
View related parts
Toyota Prius Seal, Type T Oil
Part Number: 90311-38096
$11.53 MSRP: $16.12
You Save: $4.59 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Oil(For Timing Chain Or Belt Cover)
- Replaced by: 90311-A0018
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2022 Toyota Prius | G, L, S | 4 Cyl 1.8L | 2ZRFXE; 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA, ZVW35L-BHXBBA, ZVW35L-BHXEBA, ZVW35L-BHXEBK, ZVW35L-BHXGBA, ZVW50L-AHXEBA, ZVW51L-AHXBBA, ZVW51L-AHXEBA, ZVW51L-AHXGBA, ZVW51L-AHXHBA, ZVW55L-AHXEBA, ZVW55L-AHXGBA
View related parts
Toyota Prius Seal, Engine Rear Oil
Part Number: 90311-75016
$39.28 MSRP: $54.91
You Save: $15.63 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Rear
- Replaced by: 90311-75022
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2009 Toyota Prius | 4 Cyl 1.5L | 1NZFXE; 1NZFXE; NHW11L-AEEEBA, NHW11L-AEEEBK, NHW20L-AHEEBA, NHW20L-AHEEBK
View related parts
Toyota Prius Seal, Engine Rear Oil
Part Number: 90311-76002
$47.96 MSRP: $67.03
You Save: $19.07 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Position: Rear
- Replaced by: 90311-A0013
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2014 Toyota Prius | E, G, L, S | 4 Cyl 1.8L | 2ZRFXE; 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA, ZVW35L-BHXBBA, ZVW35L-BHXEBA, ZVW35L-BHXEBK, ZVW35L-BHXGBA
View related parts
Toyota Prius Seal, Type T Oil
Part Number: 90311-78008
$43.38 MSRP: $60.63
You Save: $17.25 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Engine Rear Oil; Rear Main Seal, Rear Seal
- Manufacturer Note: *119
- Replaces: 90311-76004
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2022 Toyota Prius | G, L, S | 4 Cyl 1.8L | 2ZRFXE; 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA, ZVW35L-BHXBBA, ZVW35L-BHXEBA, ZVW35L-BHXEBK, ZVW35L-BHXGBA, ZVW50L-AHXEBA, ZVW51L-AHXBBA, ZVW51L-AHXEBA, ZVW51L-AHXGBA, ZVW51L-AHXHBA, ZVW55L-AHXEBA, ZVW55L-AHXGBA
View related parts
Toyota Prius Seal, Type T Oil
Part Number: 90311-76004
$43.38 MSRP: $60.63
You Save: $17.25 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Engine Rear Oil
- Manufacturer Note: TYPE B:REFER ILLUST.
- Replaced by: 90311-78008
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2015 Toyota Prius | G, L, S | 4 Cyl 1.8L | 2ZRFXE; 2ZRFXE; ZVW30L-AHXBBA, ZVW30L-AHXEBA, ZVW30L-AHXEBK, ZVW30L-AHXGBA, ZVW35L-BHXBBA, ZVW35L-BHXEBA, ZVW35L-BHXEBK, ZVW35L-BHXGBA

Toyota Prius Crankshaft Seal

If you are in demand for superior quality and affordable OEM Toyota Prius Crankshaft Seal, then shop with us! We own a wide range of the reduced-priced genuine Toyota Prius Crankshaft Seal. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Prius Crankshaft Seal Parts Questions & Experts Answers

Seal, Engine Rear Oil
90311-75016
Q: How do you remove and install a crankshaft pulley and oil seal on Toyota Prius?
A: Remove the Crankshaft Pulley and note how the seal is installed, ensuring the new one is positioned to the same depth and orientation. Carefully pry the oil seal out of the cover using a seal puller or a large screwdriver, taking care not to damage the crankshaft. To facilitate removal, cut the lip of the seal with a utility knife, being cautious not to distort the cover or scratch the crankshaft; wrapping electrician's tape around the screwdriver tip can help prevent damage. Apply clean engine oil or multi-purpose grease to the outer edge of the new seal and install it in the cover with the lip facing inward. Drive the seal into place using a seal driver or a large socket and hammer, ensuring it enters the bore squarely and stops at the correct depth. Check the surface on the pulley hub for any grooves caused by long-term contact with the seal, and replace the pulley if necessary. Lubricate the pulley hub with clean engine oil and reinstall the crankshaft pulley, then install and tighten the retaining bolt. The remainder of the installation follows the reverse order of removal.