Toyota 90981-13043 Bulb

You can Select Your Vehicle to check if 90981-13043 fits your vehicle.

Whenever a bulb is renewed, disconnect the battery negative lead before starting work, and remember that if the light has just been in use, the bulb may be extremely hot. Always check the bulb contacts and holder, ensuring clean metal-to-metal contact between the bulb and its live(s) and earth, cleaning off any corrosion or dirt before fitting a new bulb. For bayonet-type bulbs, ensure that the live contact(s) bear firmly against the bulb contact. Always ensure that the new bulb is of the correct rating and completely clean before fitting it, particularly for headlight and foglight bulbs. Access to the headlight bulbholders may be limited, and it may be helpful to remove the battery or at least the top clamp to improve access. Pull the wiring plug from the rear of the bulb, then remove the rubber cover. Release the bulb's wire retaining clip, pivot it down, and withdraw the bulb. When handling the new bulb, use a tissue or clean cloth to avoid touching the glass with fingers, as moisture and grease can cause blackening and rapid failure; if touched, wipe it clean with methylated spirit. Install the new bulb, ensuring its locating tabs are correctly seated, and secure it with the spring clip. Refit the rubber cover, ensuring a good seal, and reconnect the wiring plug. For the front sidelight, disconnect the wiring plug, twist the bulbholder anti-clockwise, and pull it from the rear of the headlight. Pull out the wedge-base bulb and fit a new one firmly into place, then re-secure the bulbholder. For the front direction indicator light, turn the steering wheel for better access, remove screws and clips securing the wheel arch liner, disconnect the wiring plug, twist the bulbholder anti-clockwise, and remove the bulb. Fit the new bulb, twist the bulbholder clockwise, and re-secure the wheel arch liner screws. For the front foglight, follow similar steps to gain access, disconnect the wiring plug, and twist the bulb anti-clockwise to remove it. Handle the new bulb carefully, fit it, reconnect the wiring plug, and re-secure the wheel arch liner screws. For the indicator side repeater light, slide the light unit forward against its internal spring clip, unhook its rear edge, withdraw the light unit, and disconnect the wiring plug. The bulb is not available separately, so a new light unit must be obtained if it fails. Refitting is a reversal of removal. For rear lights, open the tailgate, unclip the trim panel, twist the required bulbholder anti-clockwise to remove it, and replace any bayonet-fitting bulbs by pressing and turning them anti-clockwise. Fit the new bulb(s), clip the bulbholder back onto the light unit, and reclip the trim panel. For the number plate light, prise it from the bumper with a small screwdriver, twist the bulbholder anti-clockwise, pull out the wedge-base bulb, and press a new one into place. Refitting is a reversal of removal. For the high-level stop-light, open the tailgate, unclip the cover, remove the mounting bolt, withdraw the light, twist the bulbholder anti-clockwise, and replace the bulb by pulling the old one out and pressing in a new one. Refitting is a reversal of removal.

Remove the bulb holder and bulb.

To remove the bulb socket from the headlight housing, you need to turn it counterclockwise and pull it out of the housing.

To remove the bulb socket from the headlight housing, you need to turn it counterclockwise and pull it out of the housing.

Pry off the outer cover of the side view mirror housing, remove the turn signal mounting fasteners, and rotate the bulb counterclockwise to remove it.

The bulb has its wiring socket integrated with it, and it may only be readily obtainable from Toyota dealers.

Reach behind the headlight assembly and rotate the bulb holder counterclockwise to remove the bulb.

After replacing the low-beam bulb, you should reinstall the round rubber cover over the low-beam bulb.

Turn the fog lamp bulb holder counterclockwise and pull it out.

Remove the liftgate trim panel, then remove the high-mounted brake light mounting screws and pull the light assembly out from the rear spoiler.

Open the hood. If you're replacing the right-side headlight, remove the windshield washer reservoir for access to the bulb. If you're removing the left-side headlight, remove the cover from the fuse/relay box for access to the bulb. If that doesn't give you enough working room, you can unbolt the fuse/relay box for more access. Otherwise, the headlight housing will have to be removed. Reach behind the headlight assembly and unplug the electrical connector by depressing the clip on the harness connector.

Twist the bulb holder from the housing and replace the bulb.

These vehicles are equipped with either Halogen or LED (Light Emitting Diode) type headlamps.

Reach behind the headlight assembly and unplug the electrical connector.

2018 and later Sequoia models and some 2018 and later Tundra models use LED headlights and are not serviceable.

Twist the bulb anti-clockwise to remove it from the back of the light unit.

The bulb has its wiring socket integrated with it, and it may only be readily obtainable from Toyota dealers.

They are located in the headlight housing.