Toyota 90981-13058 Bulb

You can Select Your Vehicle to check if 90981-13058 fits your vehicle.

Disconnect the cable from the negative terminal of the battery, ensuring that the lockout feature of the anti-theft audio system is turned off if applicable. Unplug the electrical connector from the headlight bulb holder, and for T100 models, rotate the plastic bulb holder cover counterclockwise to remove it. Pull off the water shield, then remove the bulb holder retainer followed by the bulb holder and bulb. Installation is the reverse of removal, taking care not to touch the bulb with your fingers; if contact occurs, clean it with rubbing alcohol to prevent overheating and failure.

Whenever a bulb is renewed, disconnect the battery negative lead before starting work, and remember that if the light has just been in use, the bulb may be extremely hot. Always check the bulb contacts and holder, ensuring clean metal-to-metal contact between the bulb and its live(s) and earth, cleaning off any corrosion or dirt before fitting a new bulb. For bayonet-type bulbs, ensure that the live contact(s) bear firmly against the bulb contact. Always ensure that the new bulb is of the correct rating and completely clean before fitting it, particularly for headlight and foglight bulbs. Access to the headlight bulbholders may be limited, and it may be helpful to remove the battery or at least the top clamp to improve access. Pull the wiring plug from the rear of the bulb, then remove the rubber cover. Release the bulb's wire retaining clip, pivot it down, and withdraw the bulb. When handling the new bulb, use a tissue or clean cloth to avoid touching the glass with fingers, as moisture and grease can cause blackening and rapid failure; if touched, wipe it clean with methylated spirit. Install the new bulb, ensuring its locating tabs are correctly seated, and secure it with the spring clip. Refit the rubber cover, ensuring a good seal, and reconnect the wiring plug. For the front sidelight, disconnect the wiring plug, twist the bulbholder anti-clockwise, and pull it from the rear of the headlight. Pull out the wedge-base bulb and fit a new one firmly into place, then re-secure the bulbholder. For the front direction indicator light, turn the steering wheel for better access, remove screws and clips securing the wheel arch liner, disconnect the wiring plug, twist the bulbholder anti-clockwise, and remove the bulb. Fit the new bulb, twist the bulbholder clockwise, and re-secure the wheel arch liner screws. For the front foglight, follow similar steps to gain access, disconnect the wiring plug, and twist the bulb anti-clockwise to remove it. Handle the new bulb carefully, fit it, reconnect the wiring plug, and re-secure the wheel arch liner screws. For the indicator side repeater light, slide the light unit forward against its internal spring clip, unhook its rear edge, withdraw the light unit, and disconnect the wiring plug. The bulb is not available separately, so a new light unit must be obtained if it fails. Refitting is a reversal of removal. For rear lights, open the tailgate, unclip the trim panel, twist the required bulbholder anti-clockwise to remove it, and replace any bayonet-fitting bulbs by pressing and turning them anti-clockwise. Fit the new bulb(s), clip the bulbholder back onto the light unit, and reclip the trim panel. For the number plate light, prise it from the bumper with a small screwdriver, twist the bulbholder anti-clockwise, pull out the wedge-base bulb, and press a new one into place. Refitting is a reversal of removal. For the high-level stop-light, open the tailgate, unclip the cover, remove the mounting bolt, withdraw the light, twist the bulbholder anti-clockwise, and replace the bulb by pulling the old one out and pressing in a new one. Refitting is a reversal of removal.

Installation is the reverse of removal. Caution: Don't touch the bulb with your fingers. If you do, clean it with rubbing alcohol (the oil from your skin can cause the bulb to overheat and fail).

Disconnect the wiring plug from the bulbholder, twist the bulbholder anti-clockwise, and withdraw it from the light unit.

Remove the three cross-head screws at the front edge and at least two more push-in clips securing the front half of the wheel arch liner.

Grasp the bulb holder securely and rotate it counterclockwise to remove it from the housing. This step also applies to the fog lamp bulb holder.

Installation is the reverse of removal.

Open the hood. If you're replacing the right-side headlight, remove the windshield washer reservoir for access to the bulb. If you're removing the left-side headlight, remove the cover from the fuse/relay box for access to the bulb. If that doesn't give you enough working room, you can unbolt the fuse/relay box for more access. Otherwise, the headlight housing will have to be removed. Reach behind the headlight assembly and unplug the electrical connector by depressing the clip on the harness connector.

Detach the bulb from the terminals by disconnecting the electrical connector from the socket. You may need to pry the bulb out, but do so only on the ends to avoid shattering the glass.

Install a new bulb and then reinstall the lens.

Without touching the glass with your bare fingers, insert the new bulb assembly into the headlight housing, and secure it with the spring.

Remove the bulb from the headlight housing.

When handling the new bulb, be sure not to touch the glass with your bare fingers.

Disconnect the cable from the negative terminal of the battery. Caution: On models equipped with an anti-theft audio system, be sure the lockout feature is turned off before disconnecting the battery.

For installation, plug in the electrical connector that was disconnected earlier to complete the installation of the headlight bulb.

Turn the bulb body counterclockwise and remove it from the housing.

Disconnect the wiring plug, using a small screwdriver if necessary, and tape it temporarily in place to avoid it disappearing back inside the hole.

1. Remove the screws and detach the lens for bulb access. 2. Pull out the defective bulb. 3. Replace the bulb and install the lens and screws.

This is the part number 90981-13058 for your vehicle per vin. Thank You!