How to remove and install the oil pump on Toyota Celica?

To remove the oil pan, first take out the dipstick and unbolt the dipstick tube, pulling it out of the engine, especially on 4A-FE engines where it is attached to the water pump. Detach the oil pick-up tube assembly and baffle plate by removing the nuts and bolts holding them in place. Next, remove the timing belt, lower idler pulley, and crankshaft pulley, ensuring the engine is securely supported from above. Detach the oil pump case from the engine by removing the bolts, and if necessary, pry carefully between the front main bearing cap and the pump case. For engines other than 4A-FE and 7A-FE, separate the pump body from the case by removing the remaining bolts, lift out the driven rotor, and remove the O-ring. Clamp the pump pulley in a padded vise to remove the pulley nut, then take off the pulley and remove the drive rotor. For 4A-FE and 7A-FE engines, remove five screws to lift off the pump cover and then lift out the drive and driven rotors. Clean all components with solvent and inspect for wear and damage, checking the oil pressure relief valve piston sliding surface and valve spring, replacing them as a set if damaged. Measure the driven rotor-to-case and drive rotor tip clearances with feeler gauges and compare to specifications. Pry out the old oil seal and carefully drive a new seal into place, applying moly-base grease to the seal lip. For engines other than 4A-FE, install a new crankshaft seal and O-ring, lubricate the driven rotor with clean engine oil, and place it in the pump case with the mark facing out. Lubricate the shaft, install the drive rotor in the pump body, and reinstall the pulley, tightening the nut to the specified torque. Pack the pump cavity with petroleum jelly and attach the pump body to the case with the long bolts. For 4A-FE and 7A-FE engines, lubricate the rotors and place them in the pump case with the marks facing the cover, then install the cover and tighten the screws to the specified torque. Lubricate the oil pressure relief valve piston with clean engine oil and reinstall the valve components in the pump case. Place a new gasket on the engine block, position the pump against the block, and install the mounting bolts, ensuring the splines on the drive gear engage with the flats on the crankshaft. Tighten the bolts in a criss-cross pattern to avoid warping the case, then install the oil pick-up tube assembly and baffle plate with a new gasket or O-ring, tightening the fasteners to the specified torque. Reinstall the remaining parts in reverse order, add oil, start the engine, and check for oil pressure and leaks, finally rechecking the engine oil level.

Genuine Toyota Celica Oil Pump

Oil Fluid Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Oil Pumps found

View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-74050
$161.06 MSRP: $228.98
You Save: $67.92 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1999 Toyota Celica | GT, ST | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BCMGKA, ST204L-BCMGKK, ST204L-BCMSKA, ST204L-BCPGKA, ST204L-BCPGKK, ST204L-BCPSKA, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPGKK, ST204L-BLPSKA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-35020
$232.80 MSRP: $333.82
You Save: $101.02 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1985 Toyota Celica | GT, GTS, ST | 4 Cyl 2.4L | 22REC; 22REC; RA64L-BCMQEA, RA64L-BCMQEK, RA64L-BCMSEA, RA64L-BCPQEA, RA64L-BCPQEK, RA64L-BCPSEA, RA64L-BLMQEA, RA64L-BLMQEK, RA64L-BLPQEA, RA64L-BLPQEK, RA65L-BCMQEA, RA65L-BCMQEK, RA65L-BCPQEA, RA65L-BKMQEA, RA65L-BKPQEA, RA65L-BLMQEA, RA65L-BLMQEK, RA65L-BLPQEA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-88600
$154.69 MSRP: $219.92
You Save: $65.23 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2005 Toyota Celica | 4 Cyl 1.8L | 2ZZGE; 2ZZGE; ZZT231L-BLFVFA, ZZT231L-BLPVFA
View related parts
Toyota Celica Rotor Set, Oil Pump
Part Number: 15102-63010
$60.48 MSRP: $85.25
You Save: $24.77 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor
- Replaces: 15102-03010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1999 Toyota Celica | GT, GTS, ST | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SFE, 3SGELC, 5SFE; 3SFE, 3SGELC, 5SFE; ST162L-BCMSKA, ST162L-BCMSKK, ST162L-BCMVFA, ST162L-BCMVFK, ST162L-BCMVKA, ST162L-BCMVKK, ST162L-BCPSKA, ST162L-BCPSKK, ST162L-BCPVFA, ST162L-BCPVKA, ST162L-BCPVKK, ST162L-BKMVKA, ST162L-BKPVKA, ST162L-BLMVFA, ST162L-BLMVFK, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK, ST184L-BCMGKA, ST184L-BCMGKK, ST184L-BCPGKA, ST184L-BCPGKK, ST184L-BKMGKA, ST184L-BKPGKA, ST184L-BLMGKA, ST184L-BLMGKK, ST184L-BLMVKA, ST184L-BLMVKK, ST184L-BLPGKA, ST184L-BLPGKK, ST184L-BLPVKA, ST184L-BLPVKK, ST204L-BCMGKA, ST204L-BCMGKK, ST204L-BCMSKA, ST204L-BCPGKA, ST204L-BCPGKK, ST204L-BCPSKA, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLMSKA, ST204L-BLPGKA, ST204L-BLPGKK, ST204L-BLPSKA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-22041
$154.28 MSRP: $219.33
You Save: $65.05 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: (J)
- Replaced by: 15100-0D021
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2005 Toyota Celica | 4 Cyl 1.8L | 1ZZFE; 1ZZFE; ZZT230L-BLMSHA, ZZT230L-BLPSHA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-88382
$160.65 MSRP: $228.40
You Save: $67.75 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1991-1993 Toyota Celica | Turbo 4WD, Turbo All Trac | 4 Cyl 2.0L | 3SGTE; 3SGTE; ST185L-BLMVZA, ST185L-BLMVZK
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-22040
$154.28 MSRP: $219.33
You Save: $65.05 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: (J)
- Replaced by: 15100-0D021
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2003 Toyota Celica | 4 Cyl 1.8L | 1ZZFE; 1ZZFE; ZZT230L-BLMSHA, ZZT230L-BLPSHA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-74060
$161.06 MSRP: $228.98
You Save: $67.92 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1996 Toyota Celica | GT | 4 Cyl 2.2L | 5SFE; 5SFE; ST204L-BKMGKA, ST204L-BKPGKA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-16040
$215.64 MSRP: $309.21
You Save: $93.57 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1996 Toyota Celica | ST | 4 Cyl 1.8L | 7AFE; 7AFE; AT200L-BCMSKA, AT200L-BCPSKA, AT200L-BLMSKA, AT200L-BLMSKK, AT200L-BLPSKA, AT200L-BLPSKK
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-15050
$202.58 MSRP: $290.49
You Save: $87.91 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Replaces: 15100-15040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota Celica | ST | 4 Cyl 1.6L | 4AFE; 4AFE; AT180L-BCMSKA, AT180L-BCMSKK, AT180L-BCPSKA, AT180L-BCPSKK
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-16070
$216.47 MSRP: $310.41
You Save: $93.94 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1998 Toyota Celica | ST | 4 Cyl 1.8L | 7AFE; 7AFE; AT200L-BCMSKA, AT200L-BCPSKA, AT200L-BLMSKA, AT200L-BLMSKK, AT200L-BLPSKA, AT200L-BLPSKK
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-38020
$232.72 MSRP: $333.71
You Save: $100.99 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 15100-35010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1978-1979 Toyota Celica | GT, LT, ST | 4 Cyl 2.2L | 20R; 20R; RA42L-BCHDSA, RA42L-BCHQSA, RA42L-BCHSSA, RA42L-BCKDSA, RA42L-BCKSSA, RA42L-BCMQSA, RA42L-BCMSSA, RA42L-BLHQSA, RA42L-BLHSSA, RA42L-BLMQSA, RA42L-BLMSSA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-38021
$232.72 MSRP: $333.71
You Save: $100.99 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 15100-35010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1978-1985 Toyota Celica | GT, GTS, LT, ST, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 22REC, 4ME; 20R, 22R, 22REC, 4ME; MA46L-BLMQEA, RA42L-BCHDSA, RA43L-BCMQSA, RA64L-BCMQEA, RA64L-BCMQEK, RA64L-BCMQSA, RA64L-BCMQSK, RA64L-BCMSEA, RA64L-BCMSSA, RA64L-BCPQEA, RA64L-BCPQEK, RA64L-BCPQSA, RA64L-BCPQSK, RA64L-BCPSEA, RA64L-BCPSSA, RA64L-BLMQEA, RA64L-BLMQEK, RA64L-BLMQSA, RA64L-BLMQSK, RA64L-BLMSSA, RA64L-BLPQEA, RA64L-BLPQEK, RA64L-BLPQSA, RA64L-BLPQSK, RA65L-BCMQEA, RA65L-BCMQEK, RA65L-BCPQEA, RA65L-BKMQEA, RA65L-BKPQEA, RA65L-BLMQEA, RA65L-BLMQEK, RA65L-BLPQEA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-88380
$151.43 MSRP: $215.29
You Save: $63.86 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 15100-88381
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota Celica | Turbo 4WD, Turbo All Trac | 4 Cyl 2.0L | 3SGTE; 3SGTE; ST165L-BLMVZA, ST165L-BLMVZK
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-74010
$108.44 MSRP: $152.86
You Save: $44.42 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pump, Valve Lifters, Valve Spring Retainers
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1986-1996 Toyota Celica | GT, GTS, ST | 4 Cyl 2.0L, 4 Cyl 2.2L | 3SFE, 5SFE; 3SFE, 5SFE; ST162L-BCMSKA, ST162L-BCMSKK, ST162L-BCMVKA, ST162L-BCMVKK, ST162L-BCPSKA, ST162L-BCPSKK, ST162L-BCPVKA, ST162L-BCPVKK, ST162L-BKMVKA, ST162L-BKPVKA, ST162L-BLMVKA, ST162L-BLMVKK, ST162L-BLPVKA, ST162L-BLPVKK, ST184L-BCMGKA, ST184L-BCMGKK, ST184L-BCPGKA, ST184L-BCPGKK, ST184L-BKMGKA, ST184L-BKPGKA, ST184L-BLMGKA, ST184L-BLMGKK, ST184L-BLMVKA, ST184L-BLMVKK, ST184L-BLPGKA, ST184L-BLPGKK, ST184L-BLPVKA, ST184L-BLPVKK, ST204L-BCMGKA, ST204L-BCMGKK, ST204L-BCPGKA, ST204L-BCPGKK, ST204L-BKMGKA, ST204L-BKPGKA, ST204L-BLMGKA, ST204L-BLMGKK, ST204L-BLPGKA, ST204L-BLPGKK
View related parts
Toyota Celica Body Sub-Assy, Oil Pump
Part Number: 15101-16050
$170.76 MSRP: $242.76
You Save: $72.00 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: TOYODA KOUKI
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1996 Toyota Celica | ST | 4 Cyl 1.8L | 7AFE; 7AFE; AT200L-BCMSKA, AT200L-BCPSKA, AT200L-BLMSKA, AT200L-BLMSKK, AT200L-BLPSKA, AT200L-BLPSKK
View related parts
Toyota Celica Body Sub-Assy, Oil Pump
Part Number: 15101-15040
$128.14 MSRP: $182.16
You Save: $54.02 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: TOYODA KOUKI
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota Celica | ST | 4 Cyl 1.6L | 4AFE; 4AFE; AT180L-BCMSKA, AT180L-BCMSKK, AT180L-BCPSKA, AT180L-BCPSKK
View related parts
Toyota Celica Body Sub-Assy, Oil Pump
Part Number: 15111-88600
$41.79 MSRP: $58.41
You Save: $16.62 (29%)
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2003 Toyota Celica | 4 Cyl 1.8L | 2ZZGE; 2ZZGE; ZZT231L-BLFVFA, ZZT231L-BLPVFA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-41030
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1979-1981 Toyota Celica | GT, LT, Supra | 4 Cyl 2.2L, 4 Cyl 2.4L, 4 Cyl 2.7L | 20R, 22R, 4ME; 20R, 22R, 4ME; MA46L-BLMQEA, RA42L-BCHDSA, RA43L-BCMQSA
View related parts
Toyota Celica Pump Assembly, Oil
Part Number: 15100-43010
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1982-1985 Toyota Celica | Supra | 6 Cyl 2.8L | 5MGE; 5MGE; MA61L-BLMQFA, MA61L-BLMQFK, MA61L-BLPQFA, MA61L-BLPQFK

| Page 1 of 2 |Next >

1-20 of 27 Results

Toyota Celica Oil Pump

If you are in demand for superior quality and affordable OEM Toyota Celica Oil Pump, then shop with us! We own a wide range of the reduced-priced genuine Toyota Celica Oil Pump. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Celica Oil Pump Parts Questions & Experts Answers

Pump Assembly, Oil
15100-88382
Q: How to remove and install the oil pump on Toyota Celica?
A: To remove the Oil Pan, first take out the dipstick and unbolt the dipstick tube, pulling it out of the engine, especially on 4A-FE engines where it is attached to the water pump. Detach the oil pick-up tube assembly and baffle plate by removing the nuts and bolts holding them in place. Next, remove the Timing Belt, lower idler pulley, and crankshaft pulley, ensuring the engine is securely supported from above. Detach the oil pump case from the engine by removing the bolts, and if necessary, pry carefully between the front main bearing cap and the pump case. For engines other than 4A-FE and 7A-FE, separate the pump body from the case by removing the remaining bolts, lift out the driven rotor, and remove the O-ring. Clamp the pump pulley in a padded vise to remove the pulley nut, then take off the pulley and remove the drive rotor. For 4A-FE and 7A-FE engines, remove five screws to lift off the pump cover and then lift out the drive and driven rotors. Clean all components with solvent and inspect for wear and damage, checking the oil pressure relief valve piston sliding surface and valve spring, replacing them as a set if damaged. Measure the driven rotor-to-case and drive rotor tip clearances with feeler gauges and compare to specifications. Pry out the old oil seal and carefully drive a new seal into place, applying moly-base grease to the seal lip. For engines other than 4A-FE, install a new Crankshaft Seal and O-ring, lubricate the driven rotor with clean engine oil, and place it in the pump case with the mark facing out. Lubricate the shaft, install the drive rotor in the pump body, and reinstall the pulley, tightening the nut to the specified torque. Pack the pump cavity with petroleum jelly and attach the pump body to the case with the long bolts. For 4A-FE and 7A-FE engines, lubricate the rotors and place them in the pump case with the marks facing the cover, then install the cover and tighten the screws to the specified torque. Lubricate the oil pressure relief valve piston with clean engine oil and reinstall the valve components in the pump case. Place a new gasket on the engine block, position the pump against the block, and install the mounting bolts, ensuring the splines on the drive gear engage with the flats on the crankshaft. Tighten the bolts in a criss-cross pattern to avoid warping the case, then install the oil pick-up tube assembly and baffle plate with a new gasket or O-ring, tightening the fasteners to the specified torque. Reinstall the remaining parts in reverse order, add oil, start the engine, and check for oil pressure and leaks, finally rechecking the engine oil level.