What Are the Maintenance Procedures for a Driveshaft and Universal Joint on Toyota Sequoia?

A driveshaft connects the transmission and differential using universal joints. It's attached to the differential by a companion flange. 4WD models have a similar setup for the front driveshaft, while 2WD models use a splined yoke at the front. An oil seal prevents fluid leakage and dirt entry, which should be replaced if leakage is found. Two-piece driveshafts use center bearings for support. Regular lubrication and cleanliness are essential for the driveshaft.

How is the U-joint in the driveshaft replaced on Toyota Sequoia?

At first, remove the driveshaft to replace U-joint, and put it on a bench with a vise. Then mark for proper reassembly the shaft and yoke before removing snap-rings from U-joint since outer snap-rings can be taken out by use of small pliers. Select one bearing cup and place either piece of pipe or large socket over it; then go ahead and also install another socket that is little smaller in size than the first one in the opposite bearing cup, forcing this cup out using a vice up to where it stops just short of coming completely free from yoke. Apply force on the lower jaw of vise or utilize an enormous pair of pliers to take out remaining portion of the cup. Continue doing same thing for other side as well.Once these bearings cups are out, lift U-joint from yoke and clean those yokes inside them completely after which you have to remove any metal burrs from their bores.Pack new grease into U-joint bearing cups and position body of U-joint into each respective bearing partially installed in such yoke.Ensure that if there is a grease fitting, it points towards same direction as at other end's grease fitting on driveshaft.Starting into cups body of universal joint should be aligned with them finally pressing them carefully so that dust seals won't get damaged.Put back rings then tap hammer under driveshaftyolk when they are difficult to fit properly making centralize u joint.If there is grease nipple, lubricate universal joint before reinstalling drive shaft then lower car. Note that this procedure may require a press or large vice and you might want professional assistance on changing your U-Joints through repair or machine shop.

Genuine Toyota Sequoia Universal Joint

U-Joint

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Universal Joints found

View related parts
Toyota Sequoia Spider Kit, Universal Joint
Part Number: 04371-04030
$60.46 MSRP: $85.22
You Save: $24.76 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Universal Joint(For Propeller Shaft)
- Comment: (FOR PROPELLER SHAFT)
- Replaced by: 04371-04031
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA
View related parts
Toyota Sequoia Spider Kit, Universal Joint
Part Number: 04371-35051
$57.06 MSRP: $79.76
You Save: $22.70 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Rear Propeller Shaft Universal Joint
- Comment: (FOR PROPELLER SHAFT)
- Replaced by: 04371-60070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2003 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04371-0C084
$66.95 MSRP: $94.38
You Save: $27.43 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Universal Joints
- Replaces: 04371-0C094, 04371-0C080, 04371-0C081, 04371-0C082, 04371-0C093, 04371-0C090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK60L-GKALKA, 3URFE; UCK65L-GKALKA, 3URFE; UPK60L-GKTLKA, 3URFE; UPK65L-GKTLKA, 3URFE; USK60L-GKTLKA, UCK60L-GKASKA, UCK65L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, Rear Propeller Shaft Universal Joint
Part Number: 04371-0C080
$66.95 MSRP: $94.38
You Save: $27.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Rear
- Replaced by: 04371-0C084
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2011 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFE; 1URFE, 2UZFE, 3URFE; UCK60L-GKALKA, UCK60L-GKASKA, UPK60L-GKTLKA, UPK60L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04371-0C010
$72.94 MSRP: $102.82
You Save: $29.88 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Front Propeller Shaft Universal Joint
- Replaced by: 04371-04020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2005 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK35L-GKBLKA, UCK35L-GKBSKA, UCK35L-GKSLKA, UCK35L-GKSSKA, UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04375-0C041
$59.83 MSRP: $84.33
You Save: $24.50 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Front Propeller Shaft Universal Joint
- Replaced by: 04375-0C042
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2018 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04371-0C082
$66.95 MSRP: $94.38
You Save: $27.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Rear Propeller Shaft Universal Joint
- Replaced by: 04371-0C084
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2018 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04371-0C093
$66.95 MSRP: $94.38
You Save: $27.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Rear Propeller Shaft Universal Joint
- Replaced by: 04371-0C084
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2012 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, Rear Propeller Shaft Universal Joint
Part Number: 04371-0C090
$66.95 MSRP: $94.38
You Save: $27.43 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Rear
- Replaced by: 04371-0C084
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2011 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK65L-GKALKA, UCK65L-GKASKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, Front Propeller Shaft Universal Joint
Part Number: 04375-0C020
$59.83 MSRP: $84.33
You Save: $24.50 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: FRONT SIDE,REAR SIDE
- Position: Front
- Replaced by: 04375-0C042
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2011 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK65L-GKALKA, UCK65L-GKASKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, Universal Joint
Part Number: 04371-36030
$56.24 MSRP: $78.61
You Save: $22.37 (29%)
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Universal Joint(For Propeller Shaft)
- Manufacturer Note: REAR
- Comment: (FOR PROPELLER SHAFT)
- Position: Rear
- Replaced by: 04371-60210
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK45L-GKBLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Spider Kit, Universal Joint
Part Number: 04371-60070
$57.06 MSRP: $79.76
You Save: $22.70 (29%)
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Rear Propeller Shaft Universal Joint; Universal Joints
- Comment: (FOR PROPELLER SHAFT)
- Replaces: 04371-35040, 04371-35031, 04371-35050, 04371-35030, 04371-35051
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2005 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7L | 2UZFE; 2UZFE; UCK45L-GKBLKA, 2UZFE; UCK45L-GKSLKA, UCK45L-GKBSKA, UCK45L-GKSLKA, UCK45L-GKSSKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04375-0C042
$59.83 MSRP: $84.33
You Save: $24.50 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Universal Joints
- Replaces: 04375-0C030, 04375-0C020, 04375-0C040, 04375-0C041
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 4.7L, 8 Cyl 5.7L | 1URFE, 2UZFE, 3URFBE, 3URFE; 1URFE, 2UZFE, 3URFBE, 3URFE; UCK65L-GKALKA, 3URFE; UPK65L-GKTLKA, 3URFE; USK65L-GKTLGA, UCK65L-GKASKA, UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04375-0C040
$59.83 MSRP: $84.33
You Save: $24.50 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Front Propeller Shaft Universal Joint
- Replaced by: 04375-0C042
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2012 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFBE, 3URFE; 1URFE, 3URFBE, 3URFE; UPK65L-GKTLKA, UPK65L-GKTSKA, USK65L-GKTLGA, USK65L-GKTLKA, USK65L-GKTSGA, USK65L-GKTSKA, USK65L-GKTZGA, USK65L-GKTZKA
View related parts
Toyota Sequoia Spider Kit, UNIVERSA
Part Number: 04371-0C081
$66.95 MSRP: $94.38
You Save: $27.43 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Spider Kit, Rear Propeller Shaft Universal Joint
- Replaced by: 04371-0C084
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2013 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6L, 8 Cyl 5.7L | 1URFE, 3URFE; 1URFE, 3URFE; UPK60L-GKTLKA, UPK60L-GKTSKA, USK60L-GKTLKA, USK60L-GKTSKA, USK60L-GKTZKA

Toyota Sequoia Universal Joint

Universal Joint is an important assembly that is located in Toyota Sequoia models to couple the driveshaft to the transmission slip yoke and the differential yoke. Usually a small cross formed of needle bearings in steel cups and must be pre-lubricated in the factory, although some cups with grease zerks add the life span. U Joints, when in use, produce some noises such as clunks, vibrations and squeaking which are clues that the U Joints require replacement. In the advanced years, various engineers have conformed the development of the universal joint or U-joint and it has been widely recognized for use in automotive and industrial specifications.

If you are in demand for superior quality and affordable OEM Toyota Sequoia Universal Joint, then shop with us! We own a wide range of the reduced-priced genuine Toyota Sequoia Universal Joint. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Sequoia Universal Joint Parts Questions & Experts Answers

Spider Kit, Rear Propeller Shaft Universal Joint
04371-0C080
Q: What Are the Maintenance Procedures for a Driveshaft and Universal Joint on Toyota Sequoia?
A: A driveshaft connects the transmission and Differential using universal joints. It's attached to the differential by a companion flange. 4WD models have a similar setup for the front driveshaft, while 2WD models use a splined yoke at the front. An oil seal prevents fluid leakage and dirt entry, which should be replaced if leakage is found. Two-piece driveshafts use center bearings for support. Regular lubrication and cleanliness are essential for the driveshaft.
Spider Kit, UNIVERSA
04371-0C082
Q: How is the U-joint in the driveshaft replaced on Toyota Sequoia?
A: At first, remove the driveshaft to replace U-joint, and put it on a bench with a vise. Then mark for proper reassembly the shaft and yoke before removing snap-rings from U-joint since outer snap-rings can be taken out by use of small pliers. Select one bearing cup and place either piece of pipe or large socket over it; then go ahead and also install another socket that is little smaller in size than the first one in the opposite bearing cup, forcing this cup out using a vice up to where it stops just short of coming completely free from yoke. Apply force on the lower jaw of vise or utilize an enormous pair of pliers to take out remaining portion of the cup. Continue doing same thing for other side as well.Once these bearings cups are out, lift U-joint from yoke and clean those yokes inside them completely after which you have to remove any metal burrs from their bores.Pack new grease into U-joint bearing cups and position body of U-joint into each respective bearing partially installed in such yoke.Ensure that if there is a grease fitting, it points towards same direction as at other end's grease fitting on driveshaft.Starting into cups body of universal joint should be aligned with them finally pressing them carefully so that dust seals won't get damaged.Put back rings then tap hammer under driveshaftyolk when they are difficult to fit properly making centralize u joint.If there is grease nipple, lubricate universal joint before reinstalling Drive Shaft then lower car. Note that this procedure may require a press or large vice and you might want professional assistance on changing your U-Joints through repair or machine shop.