Scion 90981-11059 Bulb

You can Select Your Vehicle to check if 90981-11059 fits your vehicle.

Open the hood and reach behind the headlight assembly to unplug the electrical connector; if removing the left-side headlight, also remove the fresh-air intake duct. Release the spring clip to take out the bulb holder, then pull straight out on the bulb to remove it from the holder. Avoid touching the glass with bare fingers and use a clean lint-free cloth to hold the bulb during installation, inserting the bulb assembly into the headlight housing. Installation follows the reverse order of removal.

Open the hood and, for replacing the right-side headlight, remove the windshield washer reservoir to access the bulb. For the left-side headlight, take off the cover from the fuse/relay box for bulb access. If additional working room is needed, unbolt the fuse/relay box for more space; otherwise, the headlight housing must be removed. Reach behind the headlight assembly to unplug the electrical connector by depressing the clip on the harness connector. Rotate the plastic cover counterclockwise to detach it from the housing. Release the bulb retainer and take out the bulb from the housing, ensuring not to touch the glass of the new bulb with bare fingers. Insert the new bulb assembly into the headlight housing without touching the glass, and then plug in the electrical connector.

Carefully pry the courtesy light housing out of the door.

To remove the bulb socket from the headlight housing, you need to turn it counterclockwise and pull it out of the housing.

Make sure that the three lugs on the mounting base of the bulb socket are aligned with their corresponding cutouts in the headlight housing.

Remove the bulb holder and bulb.

To remove the bulb socket from the headlight housing, you need to turn it counterclockwise and pull it out of the housing.

Pry off the outer cover of the side view mirror housing, remove the turn signal mounting fasteners, and rotate the bulb counterclockwise to remove it.

The bulb is a push-fit in its holder; pull the old one out and press in a new one.

Pull it straight out.

Installation is the reverse of removal.

Grasp the bulb holder securely and rotate it counterclockwise to remove it from the housing. Disconnect the electrical connector, then twist the bulb holder counterclockwise and pull the holder out.

Reach behind the headlight assembly and rotate the bulb holder counterclockwise to remove the bulb.

Fit the new bulb, twisting it clockwise into the back of the light unit to secure it, then reconnect the wiring plug and refit the wheel arch liner screws.

Grasp the bulb holder securely and rotate it counterclockwise to remove it from the housing. This step also applies to the fog lamp bulb holder.

Plug in the electrical connector and insert the new bulb assembly into the headlight housing, twisting it clockwise to lock it in place.

Rotate the bulb holders counterclockwise and pull the bulbs out to remove them. Then, remove the bulb from the holder.

If there is a problem with an LED headlight, the entire headlight assembly must be replaced.

Plug in the electrical connector and, if you replaced a low-beam bulb, install the weather sealing cap.

Pull the stop light assembly straight out, disconnect the electrical connector, and remove it from the tailgate.

1. Disconnect the electrical connector from the fog light bulb holder. 2. Turn the bulb holder counterclockwise and remove it from the housing. 3. Pull the bulb straight out to remove it from the bulb holder. 4. Installation is the reverse of removal.

Remove the liftgate trim panel, then remove the high-mounted brake light mounting screws and pull the light assembly out from the rear spoiler.

On Lexus models with high-intensity discharge headlights, the low-beam bulb is accessible after unscrewing a large round cover over the bulb.

1. Detach the dome light lens. 2. Grasp the bulb securely and detach it from the spring clips at each end. 3. Installation is the reverse of removal.

If there is a problem with an LED headlight, the entire headlight assembly must be replaced.

Disconnect the cable from the negative terminal of the battery. Caution: On models equipped with an anti-theft audio system, be sure the lockout feature is turned off before disconnecting the battery.

Turn the steering wheel to give the best access to the front of the wheel arch.

Always check the bulb contacts and holder to ensure there is clean metal-to-metal contact between the bulb and its live(s) and earth. Clean off any corrosion or dirt before fitting a new bulb.

the spoiler light is an LED. unfortunately it is discontinued.