Toyota 90981-11020 Bulb

You can Select Your Vehicle to check if 90981-11020 fits your vehicle.

High beam bulbs are the inner bulbs of the headlight whereas the low-beam bulbs are the outer ones. First of all, squeeze the release tab and then remove the electrical connection of the high-beam headlight bulb. Next, release the tab in order to transform the electrical connector from the low-beam headlight bulb socket. As for the bulb socket if you want to pull it out of the headlight housing twist it anti-clockwise and then pull it out. One must not touch the bulb with bare hand; if one does, then it should be cleaned with rubbing alcohol because skin oils can cause bulb to heat up and stop working. When placing the bulb, make sure three lug terminals on the bottom of the bulb base match the similar shaped slots in the headlight housing then put the contacts in the socket and twist it as far as it is possible. It should also be noted that the process of installation is quite the opposite of the tapping technique used during the removal process.

Headlights on all these models are of the sealed beam type, so follow the replacement procedure for these bulbs. In the case of many lights, the lens is usually fixed using screws; to replace the bulbs, one has to remove the lens retainer screws; pull on the lens to disconnect it and twist the bulb in a counter-clockwise direction. Enclosures of some light assemblies share lenses installed in clips, and the clip can be unsnapped or pried off with a small screwdriver. Some bulbs can be pulled out and unscrewed in the opposite direction to install another one while the ones in the instrument cluster need the bulb holder to be twisted anti-clockwise and pulled for removal. The other bulbs are fitted on holders that are released by applying pressure in on the scaling button and turning it in anti-clockwise direction and pulling it out. Furthermore, some segments can be removed by unclipping it from such terminals or even pulling it out from the socket. To perform the procedure of checking the instrument cluster illumination lights, the instrument cluster must be pulled out.

To change the headlight bulb, the first thing is to locate the headlight bulb behind the assembly and pull out the electrical plug. Subsequent to this, unscrew the small black rubber cap which is over the headlight bulb and then use the small amount of force to pull on the spring which retains the headlight bulb to pull it out. Without coming in contact with bare fingers, place the new bulb assembly in the headlight housing and snap-in the claw spring. Next, there is rubber cover which should be installed with the tab of the 'Top Pull' directed upwards and the electrical connector must then be plugged in.

Rotate the bulb counterclockwise and pull it out, then follow the instructions for replacing an illumination bulb in the hazard flasher switch.

Reach behind the headlight assembly and rotate the bulb holder counterclockwise to remove the bulb.

Pry off the outer cover of the side view mirror housing, remove the turn signal mounting fasteners, and rotate the bulb counterclockwise to remove it.

To remove the bulb socket from the headlight housing, you need to turn it counterclockwise and pull it out of the housing.

Open the hood and reach behind the headlight assembly to unplug the electrical connector by depressing the clip on the harness connector.

To remove the bulb socket from the headlight housing, you need to turn it counterclockwise and pull it out of the housing.

Open the tailgate and unclip the trim panel from the back of the light unit.

Press and turn them anti-clockwise.

On the outside, push the license light bezel to the left to compress the clip, then withdraw the bezel and bulb holder.

Unplug the electrical connector from the bulb and holder assembly by pushing in on the center of the clip and then pulling down on the headlight bulb electrical connector.

For installation, plug in the electrical connector that was disconnected earlier to complete the installation of the headlight bulb.

Release the bulb retainer and remove the bulb from the housing. Be careful not to touch the glass of the new bulb with your bare fingers. Without touching the glass, insert the new bulb assembly into the headlight housing.

Raise the vehicle and support it securely on jackstands.

1. Work from inside the luggage compartment. 2. On the right side, remove the storage compartment cover, then pull the small inside panel free using your finger. 3. The bulb holders will be visible; turn the holder counterclockwise and remove it from the side marker assembly. 4. Pull the bulb straight out of the bulb holder.

For installation, plug in the electrical connector that was disconnected earlier to complete the installation of the headlight bulb.

Start by opening the hood and reaching behind the headlight assembly.

Pull out the wedge-base bulb and press a new one into place.

Clip the bulbholder back onto the light unit and clip the trim panel back into place.