How to remove and install piston/connecting rod assemblies on 2002 through 2008 Toyota Solara?

Remove the cylinder head, upper oil pan section, and oil pan before removing the piston/connecting rod assemblies. You can check for cylinder ridges and remove them with a tool. Make sure to measure the connecting rod endplay with feeler gauges and consult a machine shop if it exceeds the limit. Mark the connecting rods and caps for the association. Remove the connecting rod cap bolts and caps, then extract the piston/connecting rod assemblies. When installing new piston rings, verify the ring end gaps and adjust them. Install new bearing inserts and lubricate the surfaces. Also, match the assemblies and ring sets to the corresponding cylinder and insert the top ring into the first cylinder. Lubricate the piston and rings with clean engine oil and use a piston ring compressor. You should verify the connecting rod bearing oil clearance using Plastigage.

How to remove the piston/connecting rod assemblies on 1997 through 2001 Toyota Solara?

Prior to removing the piston/connecting rod assemblies, remove the cylinder head(s), the oil pan, and the oil pump pick-up tube. On four-cylinder engines only, remove the engine balancer assembly if not already done. Use your fingernail to feel if a ridge has formed at the upper limit of ring travel. If carbon deposits or cylinder wear have produced ridges, they must be completely removed with a special tool. After the cylinder ridges have been removed, turn the engine upside-down so the crankshaft is facing up. Before the connecting rods are removed, check the endplay with feeler gauges. Slide them between the first connecting rod and the crankshaft throw until the play is removed. Check the connecting rods and caps for identification marks. Loosen each of the connecting rod cap nuts 1/2-turn at a time until they can be removed by hand. Remove the number one connecting rod cap and bearing insert. To protect the crankshaft journals on four-cylinder engines, slip short pieces of rubber hose over the rod bolts before removing the pistons. Push the connecting rod/piston assembly out through the top of the engine. Repeat the procedure for the remaining cylinders. After removal, reassemble the connecting rod caps and bearing inserts in their respective connecting rods and install the cap nuts finger tight. Don't separate the pistons from the connecting rods.

How to inspect piston/connecting rod assemblies on 1997 through 2001 Toyota Solara?

Before inspection, clean the piston/connecting rod assemblies and remove the original piston rings using a piston ring installation tool. Remove carbon from the piston top with a wire brush or fine emery cloth and use a groove-cleaning tool to remove carbon deposits from the ring grooves. Clean the assemblies with solvent and dry with compressed air. If the pistons and cylinder walls are undamaged, new pistons may not be necessary, but always use new piston rings when rebuilding an engine. Inspect each piston for cracks, scoring, holes, and burned areas. Measure the piston ring groove clearance and the piston-to-bore clearance. Check the piston-to-rod clearance for wear. If pistons must be removed, have the rods checked for bend and twist. Inspect the connecting rods for damage, inspect the rod and cap bearing surfaces, and replace old bearings if necessary.

How to install piston/connecting rod assemblies on 1997 through 2001 Toyota Solara?

Before installing piston/connecting rod assemblies, clean cylinder walls, and chamfered top edges. Remove the cap from the first rod, replace bearing inserts, and clean surfaces. Check rod bearing oil clearance by fitting upper bearing inserts in the rod and cap. Arrange piston ring gaps, lubricate pistons and rings, and use a piston ring compressor during installation. Insert the piston/rod assembly into the first cylinder bore, guiding the rod to the crankshaft journal. Measure the crushed Plastigage and compare it to specifications. If clearance is incorrect, check the bearing insert size and journal diameter.

Genuine Toyota Solara Piston

Engine Pistons

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Pistons found

View related parts
Toyota Solara Piston
Part Number: 13211-0H040-A0
$94.55 MSRP: $133.29
You Save: $38.74 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13211-0H041-A0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2008 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA
View related parts
Toyota Solara Piston
Part Number: 13211-28031-B0
$94.55 MSRP: $133.29
You Save: $38.74 (30%)
ADD TO CART
Product Specifications
- Replaces: 13211-28030-B0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2007 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA
- 2001-2003 Toyota Solara | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV20L-GCMNKA, ACV20L-GCPNKA, ACV20L-GCPNKK, ACV20L-GKPNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-20030
$109.09 MSRP: $153.78
You Save: $44.69 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Piston
- Position: Passenger Side
- Replaces: 13101-0A010, 13101-20010, 13101-0A020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2003 Toyota Solara | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-GCMNKA, 1MZFE; MCV20L-GCPNKA, MCV20L-GCMNKK, MCV20L-GCPNKA, MCV20L-GCPNKK, MCV20L-GKPNKA, MCV20L-GKPNKK
View related parts
Toyota Solara Piston
Part Number: 13211-0H040-B0
$94.55 MSRP: $133.29
You Save: $38.74 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13211-0H041-B0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2008 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA
View related parts
Toyota Solara Piston
Part Number: 13211-0H040-C0
$94.55 MSRP: $133.29
You Save: $38.74 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13211-0H041-C0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2008 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-03060-01
$106.33 MSRP: $149.88
You Save: $43.55 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STD,MARK 1,(L)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2002 Toyota Solara | 4 Cyl 2.2L | 5SFE; 5SFE; SXV20L-GCMNKA, SXV20L-GCPNKA, SXV20L-GCPNKK, SXV20L-GKPNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13301-0A010
$98.01 MSRP: $138.16
You Save: $40.15 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STD,LH,(L)
- Replaced by: 13301-20020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2000 Toyota Solara | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-GCPNKA, MCV20L-GCPNKK
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13301-0A020
$98.01 MSRP: $138.16
You Save: $40.15 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side
- Replaced by: 13301-20020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2003 Toyota Solara | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-GCMNKA, MCV20L-GCMNKK, MCV20L-GCPNKA, MCV20L-GCPNKK, MCV20L-GKPNKA, MCV20L-GKPNKK
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-03060-02
$106.38 MSRP: $149.96
You Save: $43.58 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STD,MARK 2,(L)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2002 Toyota Solara | 4 Cyl 2.2L | 5SFE; 5SFE; SXV20L-GCMNKA, SXV20L-GCPNKA, SXV20L-GCPNKK, SXV20L-GKPNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-03060-03
$106.38 MSRP: $149.96
You Save: $43.58 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STD,MARK 3,(L)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2002 Toyota Solara | 4 Cyl 2.2L | 5SFE; 5SFE; SXV20L-GCMNKA, SXV20L-GCPNKA, SXV20L-GCPNKK, SXV20L-GKPNKA
View related parts
Toyota Solara Piston
Part Number: 13211-0H010-B0
$107.56 MSRP: $151.62
You Save: $44.06 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV20L-GCMNKA, ACV20L-GCPNKA, ACV20L-GCPNKK, ACV20L-GKPNKA, ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA, ACV30L-GCPGKA, ACV30L-GCPNKA
View related parts
Toyota Solara Piston
Part Number: 13211-0H010-C0
$107.56 MSRP: $151.62
You Save: $44.06 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV20L-GCMNKA, ACV20L-GCPNKA, ACV20L-GCPNKK, ACV20L-GKPNKA, ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA, ACV30L-GCPGKA, ACV30L-GCPNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-0A010
$109.09 MSRP: $153.78
You Save: $44.69 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: STD,RH,(L)
- Replaced by: 13101-20030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2000 Toyota Solara | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-GCPNKA, MCV20L-GCPNKK
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-0A020
$109.09 MSRP: $153.78
You Save: $44.69 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Passenger Side
- Replaced by: 13101-20030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2003 Toyota Solara | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-GCMNKA, MCV20L-GCMNKK, MCV20L-GCPNKA, MCV20L-GCPNKK, MCV20L-GKPNKA, MCV20L-GKPNKK
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13101-20050
$109.09 MSRP: $153.78
You Save: $44.69 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13101-0A040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2008 Toyota Solara | SE, SLE | 6 Cyl 3.3L | 3MZFE; 3MZFE; MCV31L-GCAGKA, MCV31L-GCANKA, MCV31L-GKAGKA, MCV31L-GKANKA
View related parts
Toyota Solara Piston
Part Number: 13211-28031-A0
$94.55 MSRP: $133.29
You Save: $38.74 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 13211-28030-A0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2007 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA
- 2001-2003 Toyota Solara | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV20L-GCMNKA, ACV20L-GCPNKA, ACV20L-GCPNKK, ACV20L-GKPNKA
View related parts
Toyota Solara Piston
Part Number: 13211-28031-C0
$94.60 MSRP: $133.35
You Save: $38.75 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006-2007 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA
- 2001-2003 Toyota Solara | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV20L-GCMNKA, ACV20L-GCPNKA, ACV20L-GCPNKK, ACV20L-GKPNKA
View related parts
Toyota Solara Piston
Part Number: 13211-0H010-A0
$89.22 MSRP: $125.76
You Save: $36.54 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Solara | SE, SLE | 4 Cyl 2.4L | 2AZFE; 2AZFE; ACV20L-GCMNKA, ACV20L-GCPNKA, ACV20L-GCPNKK, ACV20L-GKPNKA, ACV30L-GCAGKA, ACV30L-GCANKA, ACV30L-GCMNKA, ACV30L-GCPGKA, ACV30L-GCPNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13103-74220
$93.73 MSRP: $132.12
You Save: $38.39 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: O/S 0.50
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2002 Toyota Solara | 4 Cyl 2.2L | 5SFE; 5SFE; SXV20L-GCMNKA, SXV20L-GCPNKA, SXV20L-GCPNKK, SXV20L-GKPNKA
View related parts
Toyota Solara Piston Sub-Assy, W/Pin
Part Number: 13301-20020
Product Specifications
- Other Name: Piston
- Position: Driver Side
- Replaces: 13301-0A010, 13301-0A020, 13301-20010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2003 Toyota Solara | 6 Cyl 3.0L | 1MZFE; 1MZFE; MCV20L-GCMNKA, 1MZFE; MCV20L-GCPNKA, MCV20L-GCMNKK, MCV20L-GCPNKA, MCV20L-GCPNKK, MCV20L-GKPNKA, MCV20L-GKPNKK

| Page 1 of 2 |Next >

1-20 of 24 Results

Toyota Solara Piston

The Piston used in models such as the Toyota Solara comes as one of the many parts of the internal combustion engine, the function of which is to transform the combustion power into the required energy for the car's movement. It works by directly taking forces developed by expanding gases and converting the same into a crank shaft for proper running of the engine. Commonly made from aluminium alloys to provide strength with minimum weight, the pistons can also incorporate service holes, and cooling shafts in its structure; the piston rings may also exhibit designs such as gas sealed piston rings. A variety of designs of pistons has been incorporated in Toyota Solara models throughout the years that include trunk pistons for petrol as well as diesel engines where the part has to deal with the side forces as well as containing oil rings. Besides, racing pistons are lightweight and strong as they are made to cope with high rpm. Other types of pistons that are also used include the slipper and the deflector ones and are used in certain niches to offer the optimal performance and efficiency. All in all, the material and design of the piston determines the performance and durability of the given automobile.

If you are in demand for superior quality and affordable OEM Toyota Solara Piston, then shop with us! We own a wide range of the reduced-priced genuine Toyota Solara Piston. You can purchase in confidence as all parts come with a manufacturer's warranty. Any issues with our products? No need to worry as we have a hassle-free return policy to guide you every step of the way.

Toyota Solara Piston Parts Questions & Experts Answers

Piston
13211-28031-B0
Q: How to remove and install piston/connecting rod assemblies on 2002 through 2008 Toyota Solara?
A: Remove the cylinder head, upper oil pan section, and oil pan before removing the piston/connecting rod assemblies. You can check for cylinder ridges and remove them with a tool. Make sure to measure the connecting rod endplay with feeler gauges and consult a machine shop if it exceeds the limit. Mark the connecting rods and caps for the association. Remove the connecting rod cap bolts and caps, then extract the piston/connecting rod assemblies. When installing new piston rings, verify the ring end gaps and adjust them. Install new bearing inserts and lubricate the surfaces. Also, match the assemblies and ring sets to the corresponding cylinder and insert the top ring into the first cylinder. Lubricate the piston and rings with clean engine oil and use a piston ring compressor. You should verify the connecting rod bearing oil clearance using Plastigage.
Piston
13211-28031-B0
Q: How to remove the piston/connecting rod assemblies on 1997 through 2001 Toyota Solara?
A: Prior to removing the piston/connecting rod assemblies, remove the Cylinder Head(s), the oil pan, and the oil pump pick-up tube. On four-cylinder engines only, remove the engine balancer assembly if not already done. Use your fingernail to feel if a ridge has formed at the upper limit of ring travel. If carbon deposits or cylinder wear have produced ridges, they must be completely removed with a special tool. After the cylinder ridges have been removed, turn the engine upside-down so the crankshaft is facing up. Before the connecting rods are removed, check the endplay with feeler gauges. Slide them between the first connecting rod and the crankshaft throw until the play is removed. Check the connecting rods and caps for identification marks. Loosen each of the connecting rod cap nuts 1/2-turn at a time until they can be removed by hand. Remove the number one connecting rod cap and bearing insert. To protect the crankshaft journals on four-cylinder engines, slip short pieces of rubber hose over the rod bolts before removing the pistons. Push the connecting rod/piston assembly out through the top of the engine. Repeat the procedure for the remaining cylinders. After removal, reassemble the connecting rod caps and bearing inserts in their respective connecting rods and install the cap nuts finger tight. Don't separate the pistons from the connecting rods.
Piston Sub-Assy, W/Pin
13301-0A010
Q: How to inspect piston/connecting rod assemblies on 1997 through 2001 Toyota Solara?
A: Before inspection, clean the piston/connecting rod assemblies and remove the original piston rings using a piston ring installation tool. Remove carbon from the piston top with a wire brush or fine emery cloth and use a groove-cleaning tool to remove carbon deposits from the ring grooves. Clean the assemblies with solvent and dry with compressed air. If the pistons and cylinder walls are undamaged, new pistons may not be necessary, but always use new piston rings when rebuilding an engine. Inspect each piston for cracks, scoring, holes, and burned areas. Measure the piston ring groove clearance and the piston-to-bore clearance. Check the piston-to-rod clearance for wear. If pistons must be removed, have the rods checked for bend and twist. Inspect the connecting rods for damage, inspect the rod and cap bearing surfaces, and replace old bearings if necessary.
Piston
13211-0H010-C0
Q: How to install piston/connecting rod assemblies on 1997 through 2001 Toyota Solara?
A: Before installing piston/connecting rod assemblies, clean cylinder walls, and chamfered top edges. Remove the cap from the first rod, replace bearing inserts, and clean surfaces. Check rod bearing oil clearance by fitting upper bearing inserts in the rod and cap. Arrange piston ring gaps, lubricate pistons and rings, and use a piston ring compressor during installation. Insert the piston/rod assembly into the first cylinder bore, guiding the rod to the crankshaft journal. Measure the crushed Plastigage and compare it to specifications. If clearance is incorrect, check the bearing insert size and journal diameter.

Related Toyota Solara Parts

Browse by Year

2008 Piston 2007 Piston 2006 Piston 2005 Piston 2004 Piston 2003 Piston 2002 Piston 2001 Piston 2000 Piston 1999 Piston