Question 1

How to replace the front crankshaft seal on V6 engine on 2007 through 2015 Toyota Avalon?

Accepted Answer

First of all, remove the crankshaft pulley and pry out the seal from the timing chain cover, ensuring not scratch the crankshaft. Clean the bore in the cover and apply oil or grease to the new seal. Use a seal driver or socket to drive the new Crankshaft Seal into place with a hammer. Check the seal's spring hasn't dislodged.

Question 2

How to replace the front Crankshaft Seal on Four cylinder engine on 2002 through 2006 Toyota Avalon?

Accepted Answer

Remove the crankshaft pulley. Note how the Crankshaft Seal is installed - the new one must be installed to the same depth and facing the same way. Carefully pry the oil seal out of the cover with a seal puller or a large screwdriver. Be very careful not to distort the cover or scratch the crankshaft! Wrap electrician's tape around the tip of the screwdriver to avoid damage to the crankshaft. Apply clean engine oil or multi-purpose grease to the outer edge of the new seal, then install it in the cover with the lip (spring side) facing in. Drive the seal into place with a seal driver or a large socket and a hammer. Make sure the seal enters the bore squarely and stop when the front face is at the proper depth. Check the surface on the pulley hub that the seal rides on. If the surface has been grooved from long-time contact with the seal, a press-on sleeve may be available to renew the sealing surface. This sleeve is pressed into place with a hammer and a block of wood and is commonly available at auto parts stores for various applications. Lubricate the pulley hub with clean engine oil and reinstall the crankshaft pulley. Install the crankshaft pulley retaining bolt and tighten it. The remainder of installation is the reverse of the removal.

Question 3

How do you replace the crankshaft and camshaft oil seals on V6 engine on 2002 through 2006 Toyota Avalon?

Accepted Answer

To remove the crankshaft oil seal, remove the timing belt and sprocket. You can take out the old seal, clean the bore, and oil the seal. Use a seal driver tool for installation. Install the sprocket and belt, and check for leaks. For camshaft oil seals, remove the timing belt and sprocket. Also, remove the rear timing belt cover as well as the seal. Clean the bore, oil the new seal, and use a seal driver.

Question 4

How do you replace crankshaft and camshaft oil seals on V6 engine on 1997 through 2001 Toyota Avalon?

Accepted Answer

To remove the crankshaft oil seal, begin by undoing the timing belt as well as the sprocket. Clean the bore, oil the new seal, and install it with a seal driver tool. For camshaft oil seals, remove the timing belt and sprocket(s). Discard the rear belt cover.

Question 5

What are the steps involved in the installation process for the crankshaft seal on 1997 through 2001 Toyota Avalon?

Accepted Answer

First of all, mount the crankshaft and main bearing caps, then place the new crankshaft seal in the retainer and bolt it to the block. Also, clean the retainer and then oil the seal's edge before driving it into place. Apply a new gasket with sealant, then gradually tighten the bolts.

Question 6

How to replace the rear main oil seal on Four cylinder engine on 1997 through 2001 Toyota Avalon?

Accepted Answer

First of all, remove the transaxle when you are servicing the crankshaft seal. Another method that works involves removing the oil pan and sealing the retainer. Also, get rid of the old gasket material and the old seal. Install the new seal, lubricate the new seal, position a gasket on the engine block, and install the seal. Make sure the retainer bolts are secured and the retainer aligns with the block.

Question 7

How to replace the rear main oil seal on Four cylinder engine on 2002 through 2006 Toyota Avalon?

Accepted Answer

Remove the transmission and flywheel. You can carefully pry out the Crankshaft Seal from the engine rear, noting its depth for new seal installation. Also, clean the seal bore thoroughly. Lubricate the new seal's outer diameter and install it over the crankshaft. Use a seal installation tool to press the new seal into place. Reinstall the flywheel and transmission.

Question 8

How to replace the rear main oil seal on Four cylinder engine on 2007 through 2015 Toyota Avalon?

Accepted Answer

Remove the engine/transaxle assembly and separate the transaxle from the engine. Remove the flywheel or driveplate and pry the Crankshaft Seal from the engine's rear, noting its depth for new seal installation. Clean the seal bore thoroughly. Lubricate the new seal's outside diameter and install it over the crankshaft end, ensuring the seal lip points towards the engine. Use a seal installation tool to press the new seal into place. If unavailable, use a large socket or blunt tool to drive the seal into the bore. Reinstall the flywheel or driveplate, reattach the transaxle to the engine, and reinstall the assembly.

Question 9

How to replace the rear main seal on V6 engine on 2007 through 2015 Toyota Avalon?

Accepted Answer

First of all, remove the engine/transmission assembly and transaxle. Remove the drive plate. The Crankshaft Seal can be replaced without removing the oil pan or seal retainer. Use a seal-removal tool or a knife to cut the lip off the old Crankshaft Seal, avoiding scratching the crankshaft. Lubricate the new Crankshaft Seal and crankshaft seal journal with grease. Drive the new Crankshaft Seal into the container with a wood block or pipe. Installation is the reverse of removal.

Question 10

How to replace the front crankshaft seal on Four cylinder engine on 2007 through 2015 Toyota Avalon?

Accepted Answer

Remove the crankshaft pulley. Note how the Crankshaft Seal is installed; the new one must be installed to the same depth and facing the same way. Carefully pry the oil seal out of the cover with a seal puller or a large screwdriver. Be very careful not to distort the cover or scratch the crankshaft! Apply clean engine oil or multi-purpose grease to the outer edge of the new seal, then install it in the cover with the lip (spring side) facing in. Drive the seal into place with a seal driver or a large socket and a hammer. Make sure the seal enters the bore squarely and stops when the front face is at the proper depth. Check the surface on the pulley hub that the seal rides on. if the surface has been grooved from long-time contact with the seal. The pulley should be replaced. Lubricate the pulley hub with clean engine oil and reinstall the crankshaft pulley. Install the crankshaft pulley retaining bolt and tighten it to the torque. The remainder of installation is the reverse of removal.

Genuine Toyota Avalon Crankshaft Seal

17 Crankshaft Seals found

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Oil

Toyota Avalon Seal, Engine Rear Oil

Toyota Avalon Seal, Engine Rear Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Seal, Engine Rear Oil

Toyota Avalon Seal, Type T Oil

Toyota Avalon Crankshaft Seal

Toyota Avalon Crankshaft Seal Parts Questions & Experts Answers

Related Toyota Avalon Parts

Browse by Year